Deck ring system for keel-stepped conventional masts, E-sections and D-sections When the mast is keel-stepped, it is important to secure the deck to the mast, especially when the
halyards are led via turning blocks attached to the
deck ring. Otherwise, the lifting force of the halyards
could lift the deck. Seldén traditional deck ring
incorporates a ?tie-rod system? to eliminate this
lifting action. Rubber wedges are used to fix the
mast in the deck ring. Rails and halyard eyes are available as extras. Internal sealTapeLead blockMast coatRailHose clipHalyard eyeSupport fitting(certain sections only)Rubber chockingTie-rod Deck ring arrangements E-sections and D-sections Wedgings, mast coats, clips E-sections Deck ring (tie-rod not included) Mast No extra + Rail* 508-080 Separate rail SB or Two tie-rod rigging section function + 4 halyard eyes PS incl. bolts* screws incl. 508-023-02 backing plates Mast coat Mast Deck ring Wedging Art. No. Upper circum- Upper Hose clip section size Art. No. ference, mm seal Art. No. Rubber for wedgings E122 No ring 530-022 381 Tape Depends on avail. 25 mm deck ring size
E130 Size 1 2 x 530-205 530-022 381 312-204 E138 2 x 530-205 + 530-022 381 312-204 2 x 530-206
E155 Size 2 2 x 530-204 + 530-024 439 312-205 2 x 530-206
E170 1 x 530-204 + 530-025 473 312-205 1 x 530-205 +
1 x 530-206
E177 Size 3 2 x 530-204 + 530-026 500 312-206 2 x 530-206
E189/132B 4 x 530-202 530-027 539 312-206 E206/139B 2 x 530-202 + 530-028 568 312-20 2 x 530-203
E224 Size 4 2 x 530-202 + 530-029 630 2 x 312-202* 2 x 530-203
E237 4 x 530-202 530-030 660 2 x 312-202* E274/185B Size 5 2 x 530-202 + 530-031 752 2 x 312-203* 2 x 530-207 E130 533-008 533-008-03 Included in casting 174-042-04 E138 Size 1 Deckring is D129 187 x 144 drilled for rail + eye function
E155 533-011-01 533-011-04 508-080-01 174-042-04 E170 Size 2 D137 214 x 154
D146
E177 533-009-01 533-009-04 508-080-02* 174-042-04 E189 Size 3 E206 253 x 200
D160
E224 533-010-01 533-010-04 508-080-02* 174-042-04 E237 Size 4 302 x 232
E274 533-012-01 533-012-04 508-080-02* 174-042-04 Size 5
338 x 248 Art. No. Dim., mm 530-202 20 x 150 x 150 530-203 10 x 150 x 150 530-204 25 x 110 x 150 530-205 20 x 110 x 150
530-206 10 x 110 x 150 530-207 20 x 150 x 225 Tie-rod will take halyard load not shroud load.
U-bolt,Art. No.
508-023-02.Tie-rod,Art. No.
174-042-02.Backing plate,Art. No. 507-554-01
(Ø 6 mm).
Rail,Art. No. 508-080. Hose clips Art. No. Dim., mm min/max Deck level300Bury Q 312-202 130/165 312-203 150/180
312-204 175/205
312-205 200/231
312/206 251/282 Location of backing plate
for tie-rod.* To be spliced. * Must not be used for genoa/main/spinnaker if RM > 43 kNm. Rail 508-080 bolted through deck can be used for RM < 130 kNm. 6263