EPOXYGARD
2Pages

EPOXYGARD High protective epoxy primer with long overcoating period i?H • The printing process may render some of the colour samples imperfectly. We recommend testing the paint before committing to a colour. Nautix EPOXYGARD is "new generation" high performance 2-pack epoxy primer recommended to hull protection, and paint adhesion, especially antifouling. EPOXYGARD shapes very strong protective film with high-resistance to abrasion, particularly efficient against moisture. Easy to apply, EPOXYGARD is particularly adapted to substrates, which require high protection, below or above the waterline (GRP/Composites, aluminium, steel, and wood). Its formula has been optimized to offer a long wet on wet overcoating period to painters and it can be overcoated by itself without sanding even after few days, provided that the surface would be maintained in good condition. This margin of tolerance makes easier planning of paint jobs for shipyards. Applied in single layer, EPOXYGARD improves antifouling adhesion. Applied in several layers (3-5), this primer provides high-protection against moisture (osmosis or corrosion). d=days h=hours min=minutes *Overcoating time recommended for 1 layer (15C^m wet thickness) - Please refer to Application *If maximum overcoating time is exceeded, sand with 120 grade wet or dry paper Finish Mixing ratio (volume) Mixing ratio (weight) Coverage Flash point Unit size Typical shelf life Thinner/Cleaner Colours • GRP / Composite • Aluminium (for more details, please refer to our technical specifications for "Aluminium boat") • Steel (for more details, please refer to our technical specifications for "Steel boat") • Rigid wood (for more details, please refer to our technical specifications for "Wood boat") Technical recommendation On metal hull, it's recommended to apply this primer as soon as possible after having degreased and sanded the surface to get the best adhesion (for more details, please refer to our technical specifications for "steel" and "aluminium" boats). Important: 2-pack epoxy primer (hard finish) should not be used over any 1-pack product (soft finish). It's recommended to control humidity rate of the hull before application of several coats of primer. In case of doubts about old primer compatibility or quality, remove all the former primer. New hull (epoxy or GRP) : • The surface should be degreased with Nautix SD and free of all contaminants (oil, grease, salt etc). • Rinse with fresh water and let dry. • Sand with P120 grade paper to improve adhesion of primer. • Ensure the substrate to be dried, degreased, and free of dust. Over antifouling or existing primer : • Remove the old antifouling : 1 to 3 coats with Nautix STRIPPER, more than 4 coats with air-blasting, high-pressure water blasting or scraper. • Check the condition of old primer : the former paint must not come unstuck from the support or must not crumble. Scrape with a brush to check support quality and remove any loosing paint. • Surface must be degreased with Nautix SD and dust free. • Rough sand with 120 grit to favour adherence. • Ensure the substrate to be dried, degreased, and free of dust. • Work in well-ventilated area (ensure adequate ventilation during use), wear suitable protective clothing, gloves, glasses and eye/face protection. Unprotected person must be kept away from treatment area. Dispose of protective gloves and equipment after use. • Read the label safety section for Health and Safety Information before application. Nautix - Parc d'activites Les 5 chemins - 24 rue Nicolas Appert - 56520 Guidel, France Tel: +33.(0)2.97.65.32.69 Fax: +33.(0)2.97.65.03.54 info@nautix.com — www.nautix.com Before Printing, think about environme

EPOXYGARD High protective epoxy primer with long overcoating period Application methods : brush, roller, spray gun , airless. Apply between 10 and 30°C (ideally inside with hygrometry rate no greater than 85%). Whilst curing in high humidity conditions and at lower temperatures, epoxies can develop an ‘amine bloom’ on the surface. This slightly sticky substance must be removed with Nautix SD. Failure to remove the bloom will also make sanding more difficult. Do not apply when there is a chance of condensation forming on the substrate (Dew-Point) : substrate, ambient air and product...