Pilot II
5Pages

{{requestButtons}}

Catalog excerpts

Pilot II - 1

Technical Data Sheet Approved Pilot II Product description This is a one component oxidatively drying alkyd coating. It has a glossy finish with good gloss retention. To be used as topcoat in atmospheric environments. Typical use Recommended as topcoat, and for touch-up purposes. Marine: Recommended for engines, topside, deck and superstructure. Protective: Suitable for a wide range of industrial structures. Other Approvals and certificates Grain, Newcastle Occupational Health Food, Compliant with USA, FDA Title 21, Part 175.300 for dry solids When used as part of an approved scheme, this material has the following certification: - Low Flame Spread in accordance with EU Directive for Marine Equipment. Approved in accordance with parts 5 and 2 of Annex 1 of IMO 2010 FTP Code, or Parts 5 and 2 of Annex 1 of IMO FTPC when in compliance with IMO 2010 FTP Code Ch. 8 Consult your Jotun representative for details. Additional certificates and approvals may be available on request. Other variants available Pilot II MIO Refer to separate TDS for each variant. Colours according to colour card and Multicolor Industry tinting system (MCI) Product data Property Solids by volume Gloss level (GU 60 °) Flash point Density VOC-US/Hong Kong US EPA method 24 (tested) (CARB(SCM)2007, SCAQMD rule 1113, Hong Kong) IED (2010/75/EU) (theoretical) GB/T 23985-2009 (tested) Korea Clean Air Conservation Act (tested) (Max. thinning ratio included) VOC-EU VOC-China VOC-Korea This Technical Data Sheet supersedes those previously issued. The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com

Open the catalog to page 1
Pilot II - 2

Technical Data Sheet Pilot II The provided data is typical for factory produced products, subject to slight variation depending on colour. Gloss description: According to Jotun Performance Coatings' definition. Film thickness per coat Typical recommended specification range Dry film thickness Theoretical spreading rate Surface preparation To secure lasting adhesion to the subsequent product all surfaces shall be clean, dry and free from any contamination. Surface preparation summary table Surface preparation Substrate Minimum Clean, dry and undamaged compatible coating Coated surfaces...

Open the catalog to page 2
Pilot II - 3

Technical Data Sheet Pilot II Thinner/Cleaning solvent Thinner: Guiding data for airless spray Nozzle tip (inch/1000): Pressure at nozzle (minimum): Drying and Curing time Substrate temperature Surface (touch) dry Walk-on-dry Dry to over coat, minimum For maximum overcoating intervals, refer to the Application Guide (AG) for this product. Drying and curing times are determined under controlled temperatures and relative humidity below 85 %, and at average of the DFT range for the product. Surface (touch) dry: The state of drying when slight pressure with a finger does not leave an imprint or...

Open the catalog to page 3
Pilot II - 4

Technical Data Sheet Pilot II Packaging (typical) Volume The volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary due to local regulations. Storage The product must be stored in accordance with national regulations. Keep the containers in a dry, cool, well ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed. Handle with care. Shelf life at 23 °C Pilot II In some markets commercial shelf life can be dictated shorter by local legislation. The above is minimum shelf life, thereafter the...

Open the catalog to page 4
Pilot II - 5

Technical Data Sheet Pilot II The information in this document is given to the best of Jotun's knowledge, based on laboratory testing and practical experience. Jotun's products are considered as semi-finished goods and as such, products are often used under conditions beyond Jotun's control. Jotun cannot guarantee anything but the quality of the product itself. Minor product variations may be implemented in order to comply with local requirements. Jotun reserves the right to change the given data without further notice. Users should always consult Jotun for specific guidance on the general...

Open the catalog to page 5

All JOTUN catalogs and brochures

  1. Megafiller

    5 Pages

  2. Hardtop XP

    6 Pages

  3. SeaForce 30

    5 Pages

  4. SeaForce 60

    5 Pages

  5. SeaForce 90

    5 Pages

  6. Pioner

    4 Pages

  7. Jota Armour

    5 Pages

  8. Penguard FC

    5 Pages

  9. Tankguard DW

    6 Pages

  10. AntiPest

    5 Pages

  11. Racing

    3 Pages

  12. Megafiller

    5 Pages

  13. Osmoshell

    4 Pages

  14. MegaGloss HG

    5 Pages

  15. TopGloss

    5 Pages

  16. Megacote

    5 Pages

  17. Megasealer

    5 Pages

  18. SeaMate M

    4 Pages

  19. Hardtop AX

    5 Pages

  20. EasyPrimer

    4 Pages

  21. Marathon IQ2

    5 Pages

  22. SeaQuest

    5 Pages

  23. Hardtop One

    9 Pages

  24. Alkydprimer

    5 Pages

  25. EasyGloss

    3 Pages

  26. Aluflex

    3 Pages

  27. JOTAMASTIC

    20 Pages