INTERZONE 1000 DATA SHEET - 4 Pages

Add to MyNauticExpo favorites
INTERZONE 1000 DATA SHEET
  1. P. 1

  2. P. 2

  3. P. 3

  4. P. 4

Catalog excerpts

Glass Flake Epoxy INTENDED USES A two pack epoxy coating. Glass reinforced to provide abrasion and chemical resistance. Exhibits high build characteristics for enhanced barrier properties and physical strength. Low VOC. An abrasion resistant coating for use on above and below water vessel areas subject to corrosion as a result of mechanical damage. Suitable for marine environments subject to abrasion as well as exposure to acids, alkalis, For use at Newbuilding or Maintenance & Repair. Part B (Curing Agent) Volume Solids Typical Film Thickness Theoretical Coverage Flash Point Induction Period 3.44 volume(s) Part A to 1 volume(s) Part B 20 mils dry (21.7 mils wet), 15 - 25 mils dry practical range equivalent to 16.3 74 ft2/US gal at 20 mils dft, allow appropriate loss factors Airless Spray, Conventional Spray Part A 111°F; Part B 383°F; Mixed 133°F (Setaflash) (ASTM D-3278) 30 minutes at temperatures below 70°F Overcoating Data - see limitations Substrate Temperature Note For overcoating information consult your International Paint representative. REGULATORY DATA 75 g/lt (0.63 lb/US gal) as supplied (EPA Method 24) 70 g/kg of liquid paint as supplied. EU Solvent Emissions Directive (Council Note: VOC values are typical and are provided for guidance purposes only. These may be subject to variation depending on factors such as differences in color and normal manufacturing tolerances. Marine Coatings

 Open the catalog to page 1

Glass Flake Epoxy When used as part of an approved scheme, this product has the following certification: Fire Resistance - Surface Spread of Flame (WFR) - (IMO Resolution A653 (16)) Fire Resistance - MSC61(67) Smoke & Toxicity (WFR) Fire Resistance - Marine Equipment Directive compliant Consult your International Paint representative for details. Consult your International Paint representative for the system best suited for the surfaces to be protected. Paint only clean, dry surfaces. Remove all grease, oil, soluble contaminants and other foreign matter by "solvent For optimum performance "Near...

 Open the catalog to page 2

Glass Flake Epoxy Airless Spray Conventional Spray Maximum film build in one coat is best attained by airless spray. Application by conventional air spray may require a multiple cross-spray to attain maximum film build. Material surface and air temperatures should be in the 70-90° F range with relative humidity below 85% to attain maximum film build. Lower or higher temperatures may require specific application techniques to achieve maximum film build. Consult the following equipment recommendations or utilize suitable equal. Material is supplied in 2 containers as a unit. Always mix a complete...

 Open the catalog to page 3

Glass Flake Epoxy Apply in good weather when air and surface temperatures are above 50°F. Surface temperature must be at least 5°F above dew point. For optimum application properties, bring material to 70-80 °F prior to mixing and application. When applying by methods other than airless spray, required film build is unlikely to be achieved. Application by conventional air spray may require a multiple cross-spray pass to attain maximum film build. Overcoating information is given for guidance only and is subject to regional variation depending upon local climate and environmental conditions. Consult...

 Open the catalog to page 4

All International Marine catalogs and brochures

  1. Intergard 5000

    4 Pages

    En
  2. Intercept 7000

    1 Pages

    En
  3. Interbond 808

    2 Pages

    En
  4. Interbond 201

    2 Pages

    En
  5. Intertrac Vision

    4 Pages

    En
  6. Intersleek 1000

    6 Pages

    En
  7. Intershield 300

    8 Pages

    En
  8. Interline 9001

    6 Pages

    En
  9. Fisheries

    2 Pages

    En
  10. Interline 904

    2 Pages

    En
  11. Intershield 6GV

    2 Pages

    En
  12. Intersleek 700

    2 Pages

    En
  13. Interswift 6600

    2 Pages

    En
  14. Interspeed-5640

    2 Pages

    En
  15. Intershield 300V

    4 Pages

    En
  16. Intergard 821

    4 Pages

    En
  17. Intertherm 50

    4 Pages

    En
  18. Intergard 403

    4 Pages

    En
  19. Intersleek

    6 Pages

    En
  20. Intergard 7500

    2 Pages

    En
  21. Intergard 7020

    2 Pages

    En
  22. Interline®9001

    5 Pages

    En
  23. Interplate® Zero

    11 Pages

    En
  24. Cargo Hold

    8 Pages

    En
  25. Colour Card

    2 Pages

    En
  26. Interprime 65

    4 Pages

    En
  27. Interline 104

    4 Pages

    En
  28. Intersleek 386

    4 Pages

    En
  29. Intersleek 737

    4 Pages

    En
  30. Intersleek 970

    4 Pages

    En
  31. Interspeed 6400

    4 Pages

    En
  32. Interswift 655

    4 Pages

    En
  33. Intertuf 362

    4 Pages

    En
  34. Interswift 455FB

    4 Pages

    En
  35. INTERGARD 400

    4 Pages

    En
  36. INTERFINE 629HS

    4 Pages

    En
  37. INTERBOND 501

    4 Pages

    En

Archived catalogs

  1. Intergard 343

    9 Pages

    En