INTERLAC 678 DATA SHEET - 4 Pages

Add to MyNauticExpo favorites
INTERLAC 678 DATA SHEET

Catalog excerpts

Alkyd Varnish INTENDED USES A one pack alkyd varnish with high gloss and good durability. For interior and exterior woodwork. For use at Newbuilding, Maintenance & Repair or On Board Maintenance. Part B (Curing Agent) Volume Solids Typical Film Thickness Theoretical Coverage Flash Point High Gloss 834 ft2/US gal at 1 mils dft, allow appropriate loss factors Airless Spray, Brush, Conventional Spray, Roller Drying Information Overcoating Data - see limitations Substrate Temperature REGULATORY DATA 373 g/lt (3.11 lb/US gal) as supplied (EPA Method 24) 400 g/kg of liquid paint as supplied. EU Solvent Emissions Directive (Council Note: VOC values are typical and are provided for guidance purposes only. These may be subject to variation depending on factors such as differences in color and normal manufacturing tolerances. Marine Coatings

 Open the catalog to page 1

Alkyd Varnish SYSTEMS AND Consult your International Paint representative for the system best suited for the surfaces to be protected. SURFACE Use in accordance with the standard Worldwide Marine Specifications. PREPARATIONS A" surfaces to be coated should be clean, dry and free from contamination. High pressure fresh water wash or fresh water wash, as appropriate, and remove all oil or grease, soluble contaminants and other foreign matter in accordance with SSPC-SP1 solvent cleaning. NEWBUILDING/MAJOR REFURBISHMENT Ensure the wood is clean and dry prior to application. For new wood it is...

 Open the catalog to page 2

Alkyd Varnish Airless Spray Conventional Spray This material is a one pack coating and should always be mixed thoroughly with a power agitator before Not recommended. Use International GTA004 only in exceptional circumstances (max 15% by volume). DO NOT thin more than allowed by local environmental legislation. Total output fluid pressure at spray tip not less than 2500 psi (176 kg/cm2) Use suitable proprietary equipment. Thinning may be required. Thoroughly flush all equipment with GTA004. All unused material should be stored in tightly closed containers. Partially filled containers may...

 Open the catalog to page 3

Alkyd Varnish Overcoating information is given for guidance only and is subject to regional variation depending upon local climate and environmental conditions. Consult your local International Paint representative for specific recommendations. Apply in good weather. Temperature of the surface to be coated must be at least 5°F above the dew point. For optimum application properties bring the material to 70°F-81°F, unless specifically instructed otherwise, prior to mixing and application. Unmixed material (in closed containers) should be maintained in protected storage in accordance with...

 Open the catalog to page 4

All International Marine catalogs and brochures

  1. Intergard 5000

    4 Pages

  2. Intercept 7000

    1 Pages

  3. Interbond 808

    2 Pages

  4. Interbond 201

    2 Pages

  5. Intersleek 1000

    6 Pages

  6. Intershield 300

    8 Pages

  7. Interline 9001

    6 Pages

  8. Fisheries

    2 Pages

  9. Interline 904

    2 Pages

  10. Intershield 6GV

    2 Pages

  11. Intersleek 700

    2 Pages

  12. Interswift 6600

    2 Pages

  13. Interspeed-5640

    2 Pages

  14. Intergard 821

    4 Pages

  15. Intertherm 50

    4 Pages

  16. Intergard 403

    4 Pages

  17. Intersleek

    6 Pages

  18. Intergard 7500

    2 Pages

  19. Intergard 7020

    2 Pages

  20. Interline®9001

    5 Pages

  21. Cargo Hold

    8 Pages

  22. Colour Card

    2 Pages

  23. Interprime 65

    4 Pages

  24. Interline 104

    4 Pages

  25. Intersleek 386

    4 Pages

  26. Intersleek 737

    4 Pages

  27. Intersleek 970

    4 Pages

  28. Interspeed 6400

    4 Pages

  29. Interswift 655

    4 Pages

  30. Intertuf 362

    4 Pages

  31. INTERGARD 400

    4 Pages

  32. INTERFINE 629HS

    4 Pages

  33. INTERBOND 501

    4 Pages

Archived catalogs

  1. Intergard 343

    9 Pages