Intergard 821 - 4 Pages

Add to MyNauticExpo favorites
Intergard 821
  1. P. 1

  2. P. 2

  3. P. 3

  4. P. 4

Catalog excerpts

Intergard 821 Epoxy Filler PRODUCT DESCRIPTION A two pack epoxy filler. INTENDED USES For use as an anode shield and as a filler for pitted steel. For use at Newbuilding, Maintenance & Repair or On Board Maintenance. PRODUCT INFORMATION Part B (Curing Agent) Volume Solids 1.00 volume(s) Part A to 1 volume(s) Part B Typical Film Thickness 6000 microns dry (6000 microns wet) for use as an Anode Shield, up to 20,000 microns may be used as a filler Theoretical Coverage 0.17 m²/litre at 6000 microns dft, allow appropriate loss factors Flash Point (Typical) Part A 65°C; Part B 62°C; Mixed 62°C Induction Period Drying Information Overcoating Data - see limitations Overcoated By Intergard 821 Note REGULATORY DATA May be overcoated with Intergard and Intertuf products, consult International Paint for specific recommendations. 74 g/lt as supplied (EPA Method 24) 126 g/kg of liquid paint as supplied. EU Solvent Emissions Directive (Council Directive 1999/13/EC) 48 g/lt Chinese National Standard GB23985 Note: VOC values are typical and are provided for guidance purposes only. These may be subject to variation depending on factors such as differences in colour and normal manufacturing tolerances. Marine Coatings Page 1 of 4 Issue Date:04/12/201

 Open the catalog to page 1

Intergard 821 Epoxy Filler SYSTEMS AND COMPATIBILITY Consult your International Paint representative for the system best suited for the surfaces to be protected. SURFACE PREPARATIONS Use in accordance with the standard Worldwide Marine Specifications. All surfaces to be coated should be clean, dry and free from contamination. High pressure fresh water wash or fresh water wash, as appropriate, and remove all oil or grease, soluble contaminants and other foreign matter in accordance with SSPC-SP1 solvent cleaning. ANODE SHIELDS NEWBUILDING/MAJOR REFURBISHMENT Where necessary, remove weld spatter...

 Open the catalog to page 2

Intergard 821 Epoxy Filler APPLICATION Other Knife or Trowel Combine 1 part EAA820 with 1 part EAA821 by volume and thoroughly mix to a uniform colour. Mix only the amount that can be used within the pot life. Airless Spray Conventional Spray Work Stoppages and Cleanup Monitor material conditions, do not exceed pot life limitations. Clean all equipment immediately after use with International GTA822. In the event welding or flame cutting is performed on metal coated with this product, dust and fumes will be emitted which will require the use of appropriate personal protective equipment and adequate...

 Open the catalog to page 3

Intergard 821 Epoxy Filler LIMITATIONS This product will not cure adequately below 5°C. For maximum performance the curing temperature should be above 10°C. In humid conditions, the surface of Intergard 821 may develop a "sweat" which must be washed off with fresh water before overcoating. Overcoating information is given for guidance only and is subject to regional variation depending upon local climate and environmental conditions. Consult your local International Paint representative for specific recommendations. Apply in good weather. Temperature of the surface to be coated must be at least...

 Open the catalog to page 4

All International Marine catalogs and brochures

  1. Intergard 5000

    4 Pages

    En
  2. Intercept 7000

    1 Pages

    En
  3. Interbond 808

    2 Pages

    En
  4. Interbond 201

    2 Pages

    En
  5. Intertrac Vision

    4 Pages

    En
  6. Intersleek 1000

    6 Pages

    En
  7. Intershield 300

    8 Pages

    En
  8. Interline 9001

    6 Pages

    En
  9. Fisheries

    2 Pages

    En
  10. Interline 904

    2 Pages

    En
  11. Intershield 6GV

    2 Pages

    En
  12. Intersleek 700

    2 Pages

    En
  13. Interswift 6600

    2 Pages

    En
  14. Interspeed-5640

    2 Pages

    En
  15. Intershield 300V

    4 Pages

    En
  16. Intertherm 50

    4 Pages

    En
  17. Intergard 403

    4 Pages

    En
  18. Intersleek

    6 Pages

    En
  19. Intergard 7500

    2 Pages

    En
  20. Intergard 7020

    2 Pages

    En
  21. Interline®9001

    5 Pages

    En
  22. Interplate® Zero

    11 Pages

    En
  23. Cargo Hold

    8 Pages

    En
  24. Colour Card

    2 Pages

    En
  25. Interprime 65

    4 Pages

    En
  26. Interline 104

    4 Pages

    En
  27. Intersleek 386

    4 Pages

    En
  28. Intersleek 737

    4 Pages

    En
  29. Intersleek 970

    4 Pages

    En
  30. Interspeed 6400

    4 Pages

    En
  31. Interswift 655

    4 Pages

    En
  32. Intertuf 362

    4 Pages

    En
  33. Interswift 455FB

    4 Pages

    En
  34. INTERGARD 400

    4 Pages

    En
  35. INTERFINE 629HS

    4 Pages

    En
  36. INTERBOND 501

    4 Pages

    En

Archived catalogs

  1. Intergard 343

    9 Pages

    En