Intergard 343 - Universal Primer
4Pages

{{requestButtons}}

Catalog excerpts

Intergard 343 - Universal Primer - 1

Intergard 343 Pure Epoxy Universal Primer PRODUCT DESCRIPTION A light coloured, aluminium pure epoxy universal primer with good corrosion protection and abrasion resistance and low temperature application capability. INTENDED USES As a universal primer which can be applied directly to mechanically prepared shop primer. Suitable for use with controlled cathodic protection. For use at Newbuilding or Maintenance & Repair. PRODUCT INFORMATION Color Finish/Sheen Part B (Curing Agent) Volume Solids Mix Ratio Typical Film Thickness Theoretical Coverage Method of Application Flash Point 3 volume(s) Part A to 1 volume(s) Part B 5 mils dry (7.4 mils wet). Range 4.0-8.0 mils dry (5.9-11.8 mils wet) may be specified depending upon end use 218 ft2/US gal at 5 mils dft, allow appropriate loss factors Airless Spray, Brush, Roller Part A 82°F; Part B 99°F; Mixed 84°F Touch Dry [ISO 9117/3:2010] Hard Dry [ISO 9117-1:2009] Pot Life Overcoating Data - see limitations Substrate Temperature REGULATORY DATA VOC 329 g/lt (2.75 lb/US gal) calculated 224 g/kg of liquid paint as supplied. EU Solvent Emissions Directive (Council Directive 1999/13/EC) Note: VOC values are typical and are provided for guidance purposes only. These may be subject to variation depending on factors such as differences in color and normal manufacturing tolerances. Marine Coatings Page 1 of 4 Issue Date:3/21/2012 Ref:2875

Open the catalog to page 1
Intergard 343 - Universal Primer - 2

Intergard 343 Pure Epoxy Universal Primer CERTIFICATION When used as part of an approved scheme, this product has the following certification: • • • • • • • Food Contact - Carriage of Grain (NOHA) Tank Coatings - Recognised Corrosion Control Coating (LR) Tank Coatings - Ballast Tank type approval (GL) Tank Coatings - B1 Classification of Ballast Tank Coatings (DNV/Marintek tested) Fire Resistance - Surface Spread of Flame (WFR) - (IMO Resolution A653 (16)) Fire Resistance - MSC61(67) Smoke & Toxicity (WFR) Fire Resistance - Marine Equipment Directive compliant Consult your International...

Open the catalog to page 2
Intergard 343 - Universal Primer - 3

Intergard 343 Pure Epoxy Universal Primer APPLICATION Mixing Material is supplied in two containers as a unit. Always mix a complete unit in the portions supplied. Once the unit has been mixed it must be used within the working pot life specified. (1) Agitate Base (Part A) with power agitator. (2) Combine entire contents of Curing Agent (Part B) with Base (Part A) and mix thoroughly with power agitator. 21008_International GTA220. DO NOT thin more than allowed by local environmental legislation. Airless Spray Recommended Tip Range 21-26 thou (0.53-0.66 mm) Total output fluid pressure at...

Open the catalog to page 3
Intergard 343 - Universal Primer - 4

Intergard 343 Pure Epoxy Universal Primer LIMITATIONS UNIT SIZE Intergard 343 should be high pressure fresh water washed and/or solvent washed prior to overcoating, where necessary, to ensure removal of any surface contamination that has accumulated. Intergard 343 may be applied at substrate temperatures down to 5°F. Before applications are made below 23°F consult your local IP representative for further detail of application procedure. Overcoating information is given for guidance only and is subject to regional variation depending upon local climate and environmental conditions. Consult...

Open the catalog to page 4

All International Marine catalogs and brochures

  1. Fisheries

    2 Pages

  2. Intersleek

    6 Pages

  3. Cargo Hold

    8 Pages

  4. Colour Card

    2 Pages

  5. Intertuf 362

    4 Pages

  6. INTERLAC 678

    4 Pages

Archived catalogs