Interbond 808 - 2 Pages

Add to MyNauticExpo favorites
Interbond 808

Catalog excerpts

Tar free surface tolerant light coloured epoxy Product Description A light coloured, tar free, surface tolerant, two pack epoxy coating with high volume solids (82%). Interbond®808 can be applied as a one or two coat system over grit blasted, mechanically prepared shop primer, hydroblasted or mechanically cleaned surfaces. It is tolerant of damp surfaces. A high performance epoxy coating for use in water ballast tanks, cofferdams, void spaces, wet spaces, bilges and crude oil tanks. For use at Newbuilding, Maintenance & Repair and On Board Maintenance. Two component epoxy formulation containing aluminium pigment Long term anticorrosive performance Light colour Aids inspections and working conditions Health and safety benefits for the applicator Independent proof of performance Surface tolerant/damp tolerant Control of surface preparation costs Can be applied to damp surfaces, providing flexible scheduling, especially at sea Short time to immersion Rapid service entry Control of solvent emissions Meets regulatory requirements Excellent condition in the water ballast tank after 15 months Excellent condition in the water ballast tank after 38 months Product Information Colour Surface preparation All surfaces to be coated should be clean and free from contamination* Volume solids Typical film thickness 300 microns dry (366 microns wet) 2x160 microns dry (195 microns wet) for IMO PSPC ballast tanks Minimum application temperature 5ºC Method of application Airless Spray, Brush For each of our products the relevant Product Data Sheet, Material Safety Data Sheet and package labelling comprise an integral information system about the product in question. Copies of our Product Data Sheets and Material Safety Data Sheets are available on request or from our website. *For IMO PSPC ballast tanks consult International Paint. Wing tank - excellent condition after 48 mont

 Open the catalog to page 1

Damp Tolerance Repair Sequence Condition of ballast tanks prior to work commencing There are no scientific or electronic means of determining whether a surface is damp or wet. International Paint’s unique V test is a simple, quick assessment to evaluate whether a surface can be coated. If water collects at the bottom of the “V” the surface must not be coated. Time to Ballast TEMP (¼F) 41 TIME (DAYS) Fast time to ballasting of Interbond®808 allows rapid service entry. 2.5 Hydroblasted and corrosion removed then high pressure freshwater washed Fast time to ballasting 24 hours at 25ºC Touch up...

 Open the catalog to page 2

All International Marine catalogs and brochures

  1. Intergard 5000

    4 Pages

  2. Intercept 7000

    1 Pages

  3. Interbond 201

    2 Pages

  4. Intersleek 1000

    6 Pages

  5. Intershield 300

    8 Pages

  6. Interline 9001

    6 Pages

  7. Fisheries

    2 Pages

  8. Interline 904

    2 Pages

  9. Intershield 6GV

    2 Pages

  10. Intersleek 700

    2 Pages

  11. Interswift 6600

    2 Pages

  12. Interspeed-5640

    2 Pages

  13. Intergard 821

    4 Pages

  14. Intertherm 50

    4 Pages

  15. Intergard 403

    4 Pages

  16. Intersleek

    6 Pages

  17. Intergard 7500

    2 Pages

  18. Intergard 7020

    2 Pages

  19. Interline®9001

    5 Pages

  20. Cargo Hold

    8 Pages

  21. Colour Card

    2 Pages

  22. Interprime 65

    4 Pages

  23. Interline 104

    4 Pages

  24. Intersleek 386

    4 Pages

  25. Intersleek 737

    4 Pages

  26. Intersleek 970

    4 Pages

  27. Interspeed 6400

    4 Pages

  28. Interswift 655

    4 Pages

  29. Intertuf 362

    4 Pages

  30. INTERGARD 400

    4 Pages

  31. INTERFINE 629HS

    4 Pages

  32. INTERBOND 501

    4 Pages

Archived catalogs

  1. Intergard 343

    9 Pages