Catalogs >
International Marine >
Interbond 201 - Temperate

Interbond 201 - Temperate
4Pages

Catalog excerpts

Interbond 201 Epoxy Primer/Finish PRODUCT DESCRIPTION TEMPERATE A hard wearing, surface tolerant, two pack epoxy primer/finish offering corrosion protection in one coat. A low temperature version of Interbond 201 is available for use down to 23°F. INTENDED USES As an anticorrosive primer/finish for decks, deck fittings and cargo holds. For use at Maintenance & Repair or On Board Maintenance. PRODUCT INFORMATION Color Finish/Sheen Part B (Curing Agent) Volume Solids Mix Ratio Typical Film Thickness Theoretical Coverage Method of Application Flash Point Induction Period 4.00 volume(s) Part A to 1 volume(s) Part B 6 mils dry (8.1 mils wet) 198 ft2/US gal at 6 mils dft, allow appropriate loss factors Airless Spray, Brush, Roller Part A 82°F;Part B 93°F;Mixed 84°F (Product produced and supplied in North America has flash points of Part A 110°F, Part B 103°F and Mixed 103° F respectively due to locally sourced solvents. There is no detrimental effect on product performance.) 30 minutes at temperatures below 77°F for KDA100 Overcoating Data - see limitations 41°F Overcoated By Min Max Min Interbond 201 Ballast Holds Interbond 201 Interbond 501 Intergard 740 Intersheen 579 Interthane 990 Note Stated figures for pot life, drying times and overcoating intervals are for temperate product. For low temperature product data see separate data sheet. REGULATORY DATA VOC 279 g/lt (2.33 lb/US gal) as supplied (EPA Method 24) 229 g/kg of liquid paint as supplied. EU Solvent Emissions Directive (Council Directive 1999/13/EC) 2.29 g/lt Chinese National Standard GB23985 Note: VOC values are typical and are provided for guidance purposes only. These may be subject to variation depending on factors such as differences in color and normal manufacturing tolerances.

Open the catalog to page 1

Interbond 201 Epoxy Primer/Finish CERTIFICATION When used as part of an approved scheme, this material has the following certification: • • • • • Food Contact - Carriage of Grain (NOHH) Food Contact - FDA Compliant: Dry Foodstuffs Fire Resistance - Surface Spread of Flame (Exova Warringtonfire) Fire Resistance - Smoke & Toxicity (Exova Warringtonfire) Fire Resistance - Marine Equipment Directive compliant Consult your International Paint representative for details. SYSTEMS AND COMPATIBILITY Consult your International Paint representative for the system best suited for the surfaces to be...

Open the catalog to page 2

Interbond 201 Epoxy Primer/Finish APPLICATION Mixing Material is supplied in 2 containers as a unit. Always mix a complete unit in the proportions supplied. (1) Agitate Base (Part A) with a power agitator. (2) Combine entire contents of Curing Agent (Part B) with Base (Part A) and mix thoroughly with power agitator. International GTA220. Thinning is not normally required. Consult the local representative for advice during application in extreme conditions. Do not thin more than allowed by local environmental legislation. Airless Spray Recommended Tip Range 0.53-0.84 mm (21-33 thou) Total...

Open the catalog to page 3

Interbond 201 Epoxy Primer/Finish LIMITATIONS When spraying large areas, application of a brush coat is recommended over pitted or rough surfaces to ensure full penetration. Stripe coating of complex structures is recommended. Interbond 201 low temperature grade is not suitable for use in Ballast Holds. Optimum performance is achieved when Interbond 201 is applied over blasted steel. In common with all epoxy based coatings Interbond 201 will exhibit chalking of the film on UV exposure. Overcoating information is given for guidance only and is subject to regional variation depending upon...

Open the catalog to page 4