Interswift 655 TBT Free Antifouling PRODUCT DESCRIPTION Patented, TBT free, self polishing antifouling system incorporating unique Copper Acrylate SPC (Self Polishing Copolymer) technology. INTENDED USES For use at Newbuilding or Maintenance & Repair. In European countries where antifouling registration legislation does not permit the use of BMA002, BMA003, BMA004, BMA008, BMA009, then BMA022, BMA023, BMA024, BMA028, BMA029 must be used. Consult separate data sheet. PRODUCT INFORMATION Colour BMA002-Blue, BMA003-Green, BMA004-Dark Red, BMA008-Brown, BMA009-Black Finish/Sheen Not applicable Part B (Curing Agent) Not applicable Volume Solids 58% ±2% (ISO 3233:1998) Mix Ratio Not applicable Typical Film Thickness 125 microns dry (216 microns wet) Theoretical Coverage 4.64 m²/litre at 125 microns dft, allow appropriate loss factors Method of Application Airless Spray, Brush, Roller Flash Point Single Pack 28°C Drying Information 5°C 10°C 25°C 35°C Touch Dry [ISO 1517:73] 4.5 hrs 4 hrs 2 hrs 1.5 hrs Before Flooding 24 hrs 24 hrs 12 hrs 12 hrs 5°C 10°C Overcoating Data - see limitations Substrate Temperature 25°C 35°C Min Max Min Max Min Max Min Max Intersmooth 7460HS SPC 12 hrs ext 10 hrs ext 6 hrs ext 4 hrs ext Interswift 655 12 hrs ext 10 hrs ext 6 hrs ext 4 hrs ext Overcoated By Note REGULATORY DATA For Intersmooth 360, 365, 460, 465 and 7465HS SPC follow the overcoating interval data given for Intersmooth 7460HS SPC. When BMA002-Blue, BMA003-Green and BMA009-Black are overcoated with themselves a maximum overcoating interval of 1 month must be observed. (see Limitations) VOC 381 g/lt as supplied (EPA Method 24) 207 g/kg of liquid paint as supplied. EU Solvent Emissions Directive (Council Directive 1999/13/EC) Note: VOC values are typical and are provided for guidance purposes only. These may be subject to variation depending on factors such as differences in colour and normal manufacturing tolerances. This product does not contain organotin compounds acting as biocides and as such is in compliance with the International Convention on the Control of Harmful Anti-fouling Systems on ships as adopted by IMO in October 2001 (IMO document AFS/CONF/26). Marine Coatings Page 1 of 4 Issue Date:11/08/2010 Ref:787

Interswift 655 TBT Free Antifouling CERTIFICATION When used as part of an approved scheme, this material has the following certification: Product recognised by the following classification societies as compliant with the International Convention on the Control of Harmful Anti-fouling Systems on Ships, 2001 (AFS 2001): • • • • • Lloyds Register Germanischer Lloyd Korean Register of Shipping Det Norske Veritas Bureau Veritas Consult your International Paint representative for details. SYSTEMS AND COMPATIBILITY Consult your International Paint representative for the system best suited for the surfaces...

Airless Spray Conventional Spray This material is a one pack coating and should always be mixed thoroughly with a power agitator before Not recommended. Use International GTA007 only in exceptional circumstances and as advised by the International Paint Technical Service representative. DO NOT thin more than allowed by local environmental Total output fluid pressure at spray tip not less than 176 kg/cm2 (2500 p.s.i.) Application by conventional spray is not recommended. Application by brush is recommended for small areas only. Multiple coats may be required to achieve specified film thickness....

Interswift 655 TBT Free Antifouling LIMITATIONS If the following maximum recommended exposure times before flooding are exceeded, antifouling performance may be impaired: Tropical conditions - 3 months Temperate conditions - 6 months If these times are exceeded, close high pressure fresh water wash (at 3,000 p.s.i., 211 kg/cm²) the surface before immersion. The maximum overcoating interval of 1 month when BMA002-Blue, BMA003-Green and BMA009-Black are applied to themselves may be extended provided that the coating is suitably treated prior to overcoating. (Consult International Paint) Interswift...