Catalogue G2 User Manual
www.glascraft.com
print switch display
Page / 36
Contact the
Manufacturer		 Where to buy
this product ?		 Request
a Quote
GlasCraft -
/ 36
See other catalogues for GlasCraft
Text version of the page
Operation
11. Remove Cap, Catalyst Ring, Spray Tip and Spacer □ FINAL PRESSURE TYPICALLY RANGES FROM 30 from the gun. (refer to gun manual) TO 45 PSI DEPENDING ON MATERIAL USED.
Fig. 3
15. Slowly increase Air Assist Air Pressure Regulator until tails disappear from spray pattern. (See Fig. 4)
12. Trigger the Gun until a steady material stream ap­pears at the Nozzle Body. Material Regulator should initially be set not to exceed 10 PSI.
Typical Spray Pattern Development
(with Air Assist)
STEP AIR ASSIST ADJUSTMENT
PATTERN
PRESSURE ADJUSTMENT
CLOSED
i
INCREASE
13. Once a steady material stream is achieved,
release trigger and re-assemble all parts removed from the gun.
15 PSI
2
INCREASE
30 PSI
CORRECT
3
CAUTION
Cap, P/N LPA2-213, should be HAND TIGHTENED ONLY. Never use a wrench or pliers to assemble, tight -en or remove this cap. If threads are clean and lubri -cated properly, hand assembly and removal will not be a
problem.
Use of wrenches or pliers will likely cause serve dam -age to the threads and/or Gun Head.
FINAL AIR ASSIST ADJUSTMENT IS COMPLETE WHEN TAILS ARE ELIMINATED AND A UNIFORM SPRAY PATTERN IS ACHIEVED. FINAL PRESSURE TYPICALLY RANGES FROM 30 TO 45 PSI DEPEND­ING ON MATERIAL USED.
Fig. 4
NOTE
Follow step 16. if optional catalyst bottle is being used.
14. Slowly increase resin pressure regulator until desired spray pattern is achieved. (See Fig. 3)
Typical Spray Pattern Development
(without Air Assist)
16. Safely fill the Catalyst Supply Bottle, P/N LPA-165 (maximum two gallons) with preferred MEKP catalyst to a minimum level at least one inch above Catalyst Bottle Outlet Fitting.
STEP RESIN PATTERN PRESSURE
PRESSURE ADJUSTMENT
WARNING
Remove Catalyst Bottle, P/N LPA-167-01, from Catalyst Bottle Bracket, P/N LPA-169, for filling.
Bottle should be placed at or below waist-level for safe fill­ing.
Never fill Catalyst Bottle while mounted in Bracket as per­sonal injury from catalyst spillage could result.
1
20 PSI
INCREASE
2
25 PSI
INCREASE
30 PSI
3
INCREASE
35 PSI*
4
CORRECT
23
NauticExpo's Virtual Library: PDF Catalogues | Documentation | Boating Brochures | Manuals | Marine directory | Specifications | Characteristics
Search Go
page 1 p.1
page 2 p.2
page 3 p.3
page 4 p.4
page 5 p.5
page 6 p.6
page 7 p.7
page 8 p.8
page 9 p.9
page 10 p.10
page 11 p.11
page 12 p.12
page 13 p.13
page 14 p.14
page 15 p.15
page 16 p.16
page 17 p.17
page 18 p.18
page 19 p.19
page 20 p.20
page 21 p.21
page 22 p.22
page 23 p.23
page 24 p.24
page 25 p.25
page 26 p.26
page 27 p.27
page 28 p.28
page 29 p.29
page 30 p.30
page 31 p.31
page 32 p.32
page 33 p.33
page 34 p.34
page 35 p.35
page 36 p.36
pdf-page pdf ne En 2008-12-49-03