FIX 30
3Pages

TECHNICAL DATA SHEET FIX 30 Revision: 01/2011 Technical Data: Base Consistency Curing system Open Time @ 21° and 50% R.H (*) Adjustability Time @ 21° and 50% R.H (*) Specific Gravity (DIN 53479) Viscosity (Brookfeild mPa.s) Elongation at Break Application Rate Total Solids Content Temperature Resistance (cured) Durability Against Aging Set to Load Bearing Sanding Finishing Shear Strength: (*) Values may vary depending on environmental conditions. Product: Fix 30 is a solvent and water free universal flexible adhesive. Suitable for bonding many types of timber, stone, marble, granite and other products onto a variety of substrates. It is ideal for exotic timbers and suitable for external and internal applications for marine, transport and construction industries. Ability to feather edge build without shrinkage or cracking, sound absorbtion, impact resistance and flexibility. Fix 30 cures by means of a chemical reaction within the adhesive. Once cured (approx. 24hrs @ 21°C and 50% R.H) an elastic non shrinkable adhesive layer is formed, which is resistant to heat and moisture. Characteristics: - Ready to use - Single component - EC-1 labal, very low emissions - Solvent free - Water free - Free of Isocyanates - Easy application - Feather edge to 10mm Page 1 of 2 SMX Polymer Paste Chemical Cure Approx. 30-40 minutes Approx. 10 minutes Appox. 1.65g/cm Approx. 56.000 (HBT A/10) Approx. 300% 800-1200g/m2 depending on substrate 100% (solvent free) -40°C to 90°C Good Min. 12hrs Min. 12 Hrs > 1.5 N/mm2 - Form stable peaks when applied by notched trowel - Rapid cure and buildup of final bond strength - Permanently elastic - Suitable for marine teak decks - Suitable for parquetry flooring systems - High final bond strength (DIN 281) Applications: Fix 30 is suitable for bonding all types of wooden and stone floors and walls such as solid, prefinished parquet wood plank, granite, marble and laminates. Suitable for use on porous and nonporous surfaces such as mosaic, anhydrite, concrete screeds, timber, fibreglass, aluminium, Medium Density Fibre Board (MDF) Applications continued: steel, granite, marble and floors with underfloor heating. Packaging: Packaging – 600mL foil bag Note: The contents contained in this documentation are the result of our experiments and our experienceand have been submitted in good faith. Because of the diversity of the materials and substrates and the real number of possible applications which are out of our control we cannot accept any responsibility for the results obtained. In every case it is recommended to carry out preliminary experiments and compatibility tests. Fixtech Pty Ltd. PO Box 568, Southport, Qld 4215. Tel: +61 (0)7 5530 1099. Fax: +61 (0)7 5530 1322 Email: info@fixtech.com.au Web: www.fixtech.com.au

TECHNICAL DATA SHEET FIX 30 Revision: 01/2011 Shelf life: 12 months foil bags In unopened packaging in a cool and dry storage place a t temperatures between +5°C and +25°. Substrate: Before installation of the adhesive the surface should be checked to ensure suitability. Check the moisture content of the entire substrate with a carbide or electric hygrometer. The moisture content must be as recommended by the covering manufacturer. Max 2% for sand and cement surfaces; max 0.5% for anhydrite. For substrates with underfloor heating max values are 1.5% and 0.3% respectively. Fix 30 should be...

TECHNICAL DATA SHEET FIX 30 Revision: 01/2011 Recommendations continued: - Do not install to substrates with a moisture content exceeding manufacturer or supplier recommendations. Do not install to substrates with moisture content under 7%. Do not install in areas directly after painting or plastering Do not dilute the adhesive Do not use paint prep in the preparation of timber substrates and coverings. Page 3 of 3 Application: Method: Manual or pneumatic caulking gun Application temperature: +15°C to 35°C Clean up: Methylated Spirits or alcohol cleaner immediately after application and...