Double Coat Modellak - 3 Pages

Add to MyNauticExpo favorites
Double Coat Modellak

Catalog excerpts

DOUBLE COAT MODELLAK DESCRIPTION Double Coat Modellak is a high gloss two component finish based on saturated polyester resins and modified aliphatic isocyanate hardeners, especially developed for models and moulds. PRINCIPAL CHARACTERISTICS Excellent levelling, easy application by spray; Good resistance to various chemicals; In combination with Double Coat Modellak hardener within 24 hours resistant to gelcoat and styrene, see additional information; Excellent scratch and mar resistance; Excellent gloss and colour retention; Excellent adhesion to GRP, wood, MDF and Poltix fillers; Suitable as coating system for models used for the production of moulds for the GRP industry. COLOURS AND GLOSS RAL 1001 beige - High gloss BASIS PROPERTIES (AT Density Solid content Recommended d.f.t. Dust dry after Full cure after Recoating interval 23˚C AND 50% R.H.) : approx. 1,3 g/cm3 : approx. 59 % (volume) : 35 - 50 µm (dry), depending on application : approx. 30 minutes : approx. 7 days, see additional information : min. 24 hours, see additional information max. unlimited, provided gritpapered, clean and dry Shelf life : separate components, stored cool an dry in original packaging, minimum 12 months Flash point (DIN53213) : Double Coat Modellak base component 44 oC Double Coat Modellak hardener 1 oC SPREADING RATE At 35 µm (d.f.t.) : 12,9 m2/kg (14,8 m2/l) At 50 µm (d.f.t.) : 8,6 m2/kg (10,4 m2/l) The practical spreading rate depends on a number of variables, such as: shape and size of object to be painted, the condition and profile of the substrate, the method of application, climatologic conditions and skill of labour. SUBSTRATE CONDITION AND TEMPERATURE All substrates : clean and dry, in good condition, free from any contamination and loose particles, degreased with Double Coat Degreaser and pre-treated with IJmopox ZF primer/IJmopox HB coating, Poltix Sprayfiller or IJmofix and sanded with grit paper P300-320; During application and curing a minimum temperature of 15 ºC is allowed. The temperature of the substrate should be minimum 3 ºC above dew point. INSTRUCTIONS FOR USE Before use, mix base and hardener components thoroughly. Mixing ratio : 67,0 base : 33,0 hardener (by weight) 63,0 base : 37,0 hardener (by volume) Do not prepare more material than can be applied within the pot life of the mixture.

 Open the catalog to page 1

DOUBLE COAT MODELLAK Induction time Pot life Application with Type thinner % of thinner Nozzle orifice Nozzle pressure Cleaning none 3 hours at 25 ºC 4 hours at 20 ºC 5 hours at 15 ºC : Brush/roller1 Spray thinner 3-5% n.a. n.a. Spray thinner Air spray Spray thinner 5 - 15 % 1,4 – 1,6 mm 2 - 3 bar Spray thinner Application by brush or roller is only possible in combination with Double Coat hardener ADDITIONAL INFORMATION Recoating and curing of Double Coat Modellak Minimum Maximum, without sanding Maximum, after sanding with grit paper P320-P400 Styrene resistant after2 Styrene resistant...

 Open the catalog to page 2

DOUBLE COAT MODELLAK Resistance to styrene Double Coat Modellak is recommended for models used to produce moulds for the GRP industry. For this specific application it is imperative that all materials used in the paint system for the model resist styrene. When a component does not resist styrene, this can lead to serious surface defects in model or mould. SAFETY INFORMATION See the corresponding Material Safety Data Sheet for detailed instructions on safety, disposal and health. Date: October ’11 422-99999 Disclaimer Although the information and recommendations are presented in good faith...

 Open the catalog to page 3

All De IJssel Coatings catalogs and brochures

  1. TWEECOLUX

    3 Pages

  2. Epoxy Gel

    3 Pages

  3. Balsaplast

    2 Pages

  4. KARAAT

    2 Pages

  5. DUBBEL UV

    2 Pages

  6. DOUBLE COAT

    2 Pages