Trophy Touch Up Pressure - 72 Pages

Add to MyNauticExpo favorites
Trophy Touch Up Pressure
  1. P. 1

  2. P. 2

  3. P. 3

  4. P. 4

  5. P. 5

  6. P. 6

  7. P. 7

  8. P. 8

  9. P. 9

  10. P. 10

  11. P. 20

  12. P. 30

  13. P. 40

  14. P. 50

  15. P. 60

  16. P. 70

Catalog excerpts

SERVICE MANUAL BINKS “TROPHY” SERIES PRESSURE AND SIPHON FEED HVLP & LVMP TOUCH-UP SPRAY GUNS (1465-XXXX-XXXX) II 2 G X Binks Trophy Series Touch-up Spray Gun is the premier spray gun for use in pressure feed touch-up and light production spray applications and sets a new standard in durability, ergonomics, and atomization. The lightweight ergonomic design offers unsurpassed comfort and control. The latest advanced atomization technology has been incorporated for achieving consistent, fine finishes when spraying a wide range of industrial coating applications. Binks Trophy Series Touch-up Spray Guns can be used with pumps, pressure pots, pressure cups, or siphon cups. Binks Trophy Series Touch-up Spray Guns are offered in two different atomization technologies: HVLP and LVMP. SPECIFICATIONS Maximum Air Pressure Maximum Fluid Pressure Anodized Aluminum Fluid Path Stainless Steel Fluid Inlet Size Wetted Parts The Trophy HVLP Series of Spray Guns can be used to operate at high transfer efficiencies in compliance with “California South Coast Air Quality Management District” regulations as a High Volume, Low Pressure spray gun. Stainless Steel & PTFE IMPORTANT! DO NOT DESTROY It is the customer's responsibility to have all operators and service personnel read and understand this manual. Contact your local Binks representative for additional copies of this manual. READ ALL INSTRUCTIONS BEFORE OPERATING THIS BINKS PRODUCT.

 Open the catalog to page 1

EN In this part sheet, the words WARNING, CAUTION and NOTE are used to emphasize important safety information as follows: Hazards or unsafe practices which could result in severe personal injury, death or substantial property damage. Hazards or unsafe practices which could result in minor personal injury, product or property damage. Important installation, operation or maintenance information. Read the following warnings before using this equipment. READ THE MANUAL Before operating finishing equipment, read and understand all safety, operation and maintenance information provided in the operation...

 Open the catalog to page 2

EN TYPES OF INSTALLATION Air pressure for atomization is regulated at the extractor. The flow of the fluid is adjusted by the fluid valve control knob on gun, viscosity of paint and air pressure. PRESSURE CUP HOOKUP (Figure 1) For fine finishing with limited spraying. Air pressure for atomization is regulated at extractor; fluid pressure at cup regulator. Pressure cup is also available less regulator. PRESSURE TANK WITH 2 REGULATORS (Figure 2) Pressure Tank The pressure to the tank is regulated by the first regulator. The pressure for atomization is regulated by the second regulator. PRESSURE...

 Open the catalog to page 3

EN BINKS “TROPHY” SERIES TOUCH-UP SPRAY GUN The fluid inlet is not meant to be removed or replaced. SELECTION GUIDE FOR BINKS “TROPHY” SERIES TOUCH-UP SPRAY GUNS TYPE OF FLUID TO BE SPRAYED COMPLETE GUN ASSEMBLY PART NUMBER SPRAY TECHNOLOGY VERY LIGHT/Reduced Flow Stains, varnishes, thin lacquers, automotive refinishing materials SPRAY TECHNOLOGY General industrial coatings, Enamels, Epoxies, Fine grit ceramics Low VOC coatings, Adhesives, Fine grit ceramics COMPLETE GUN ASSEMBLY PART NUMBER TYPE OF FLUID TO BE SPRAYED Greater than 30 seconds, Zahn 2 • Plastic Tip Needle Set-ups

 Open the catalog to page 4

EN CHART 1: BINKS “TROPHY” SERIES TOUCH-UP SPRAY GUN PARTS LIST ITEM NO. PART NUMBER AIR CAP RETAINING RING ASSEMBLY SEE CHARTS BELOW SEE CHARTS BELOW FLUID NOZZLE SIDE PORT VALVE ASSEMBLY PART NUMBER KNOB – NEEDLE ADJUSTING + SIDE PORT STEM AIR ADJUSTING VALVE ASSEMBLY FRONT SEAL – AIR VALVE FRONT AIR VALVE SEAL GUN BODY WITH FLUID INLET TOOL – SEAL INSERTION GUNNER'S MATE (3 CC TUBE) REAR SEAL – AIR VALVE NEEDLE – STAINLESS STEEL (STD.) TO CONVERT TO SIPHON FEED, PURCHASE CUP 81-384, SOLD SEPARATELY. + PARTS INCLUDED IN 54-6216 n PARTS INCLUDED IN 54-6130-K t ALSO AVAILABLE IN KIT OF 3: SN-2-K3...

 Open the catalog to page 5

6. Adjust inlet air pressure if required. 7. Turn fluid adjusting knob counter clockwise until first thread shows. 8. Test spray. If the finish is too dry, reduce airflow by reducing air inlet pressure. 9. finish is too wet, reduce fluid flow by turning fluid If adjusting knob (24) clockwise. If atomization is too coarse, increase inlet air pressure. If too fine, reduce inlet pressure. 10. he pattern size can be reduced by turning sideport T control (9) clockwise. 11. old gun perpendicular to surface being sprayed. Arcing H or tilting may result in uneven coating. 12. he recommended spray distance...

 Open the catalog to page 6

REMOVAL AND INSTALLATION PROCEDURES NEEDLE AND VALVE DISASSEMBLY AND ASSEMBLY FIG.1

 Open the catalog to page 7

EN MAINTENANCE – FLUID NOZZLE AND BAFFLE REMOVAL AND INSTALLATION FIG.1

 Open the catalog to page 8

EN MAINTENANCE – NEEDLE PACKING REMOVAL AND INSTALLATION FIG.1 MAINTENANCE – SIDEPORT REMOVAL AND INSTALLATION FIG.1

 Open the catalog to page 9

Heavy top or bottom pattern Horn holes plugged. Obstruction on top or bottom of fluid tip. Cap and/or tip seat dirty. Clean. Ream with non-metallic point. Clean. Clean. Heavy right or left side pattern Left or right side horn holes plugged. Dirt on left or right side of fluid tip. Clean. Ream with non-metallic point. Clean. Remedies for the top-heavy, bottom-heavy, right-heavy, and left-heavy patterns: 1. etermine if the obstruction is on the air cap or the fluid tip. Do this by making a test D spray pattern. Then, rotate the cap one-half turn and spray another pattern. If the defect is inverted,...

 Open the catalog to page 10

Starved spray pattern Inadequate material flow. Back fluid adjusting screw out to first thread, or change to larger tip size. Increase air pressure and rebalance gun. Low atomization air pressure. Excessive overspray Too much atomization air pressure. Reduce pressure. Gun too far from work surface. Adjust to proper distance. Improper stroking (arcing, gun motion too Move at moderate pace, parallel to work fast). surface. Too much or too fast-drying thinner. Too much atomization (air pressure.) Remix properly. Reduce air pressure. Air pressure too high. Gun tip too far from work surface. Gun motion...

 Open the catalog to page 11

Removes water, oil, and debris Contains six precision tools designed to effectively clean all DeVilbiss, Binks, Finishline and other brand spray guns. Twin Cartridge Paint Spray Respirator NIOSH-Certified, for respiratory protection in atmospheres not immediately danger- Small Medium Large High Flow Type Mate Lube petroleum distillates MSDS available upon Hand Cleaner Towels hand cleanertowel for painters, Adjusting Valve pressure gauge. Use to control Optional Siphon Cups Features wide bottom Star wheel and yoke closure. DeKups Accessories for siphon feed cups

 Open the catalog to page 12

All Binks catalogs and brochures

  1. MX1212 Pump System

    24 Pages

    En
  2. MX412 Pump System

    28 Pages

    En
  3. Model 7 Spray Gun

    12 Pages

    En
  4. Trophy Siphon

    80 Pages

    En
  5. Trophy Gravity

    80 Pages

    En
  6. Trophy Pressure

    80 Pages

    En
  7. GEMS 240-5100

    16 Pages

    En
  8. MAG AA Automatic

    8 Pages

    En

Archived catalogs

  1. Trophy series

    10 Pages

    En