Pneumatic Diaphragm Pump - 12 Pages

Add to MyNauticExpo favorites
Pneumatic Diaphragm Pump
  1. P. 1

  2. P. 2

  3. P. 3

  4. P. 4

  5. P. 5

  6. P. 6

  7. P. 7

  8. P. 8

  9. P. 9

  10. P. 10

Catalog excerpts

Binks PNEUMATIC DIAPHRAGM PUMP Read and follow all instructions, recommendations and safety precautions before using this equipment. It is the responsibility of the employer to place this information into the hands of the operator. Anodized Aluminum Pump Models: DVPS-US-C Pail Mounted - No Agitator DVPS-US-CA Pail Mounted - With Agitator DVPE-US Wall Mounted Be sure that all fluids, solvents and fillers to be used are chemically and physically compatible with wetted parts in the DVP pump. Consult your BINKS representative for DVP pump materials of constructions and compatibility information. Consult the fluid manufacture for information regarding the fluids to be used. BINKS is not responsible for misapplication of DVP pumps. Consult your BINKS representative for application assistance. This is an air operated diaphragm pump, suitable for up to two guns or small circulation systems. Its wetted materials are anodized aluminum and PTFE. IMPORTANT: If you are using the pump with corrosives or abrasives materials, you will need to clean the pump more often or replace parts more frequently. The maximum surface temperature of the pump will depend on the temperature of the fluid being pumped. Max fluid temperature allowed is TECHNICAL DATA: Basic pump Basic pump w/ Pail Basic pump w/ Pail and Agitator NOTE: Weights and dimensions are approximate. Max paint viscosity (ford N°4) Universal threaded air connector 1/4"(m) NPS Ambient temp range operating speed: Cycle/min. Max. fluid flow (water free open) 17 l/min 4.49 gpm Universal fluid threaded connector 3/8"(m) NPS The chart below shows the relation between the air consumption and the material flow rate and number of cycles. Example: At an air input pressure of 5 bar (72.5 psi) and material flow rate of 8.3 l/min (2.19 gpm), at 60 cycles/min, Cycling Speed (cycles/min) Part Sheet

 Open the catalog to page 1

In this part sheet, the words WARNING, CAUTION and NOTE are used to emphasize important safety information as follows: Hazards or unsafe practices which could result in severe personal injury, death or substantial property damage. Hazards or unsafe practices which could result in minor personal injury, product Important installation, operation or maintenance information. Read the following warnings before using this equipment. Before operating finishing equipment, read and understand all safety, operation and maintenance information provided in the operation manual. WEAR SAFETY GLASSES Failure...

 Open the catalog to page 2

SAFETY INSTRUCTION: Binks PNEUMATIC DIAPHRAGM PUMP DVP-GEMINI Important: Read and follow all instructions, recommendations and safety precautions before using this equipment. It is the responsibility of the employer to place this information into the hands of the operator. Solvents and coating materials can be highly flammable or combustible, especially when sprayed. Work stations must be provided with adequate ventilation/exhaust to prevent the build-up of flammable vapors. Smoking and open flames must not be allowed in the spraying or mixing areas. Fire extinguishing equipment must be provided...

 Open the catalog to page 3

Binks PNEUMATIC DIAPHRAGM PUMP DVP – GEMINI 4

 Open the catalog to page 4

Binks PNEUMATIC DIAPHRAGM PUMP DVP-GEMINI PARTS LIST (CONDUCTIVE PLASTIC) (WITH SNAP RING) The contents of repair kits are identified with letters A Example: kit KK-4630 ("B") is made up of part numbers identified with the letter "B". (See chart above.) (WITH SNAP RING) (2 SCREWS, 4 WASHER, 4 NUTS & GROUNDING WIRE) Use a medium strength sealing compound an threaded joints to prevent leakage. Kit of Spares (misc. parts)

 Open the catalog to page 5

Binks PNEUMATIC DIAPHRAGM PUMP DVP-GEMINI MODEL WITHOUT AGITATOR These products include air regulator, muffler, carrying handle, suction tube with filter, by-pass with fluid return tube, 5 gallon pail cover, and a MODEL WITH AGITATOR These products include air regulator, muffler, carrying handle, suction tube with filter, by-pass with fluid return tube, agitator assembly, 5 gallon pail cover, and a 5 gallon pail. MODEL FOR WALL MOUNTING These products include air regulator, carrying handle, combination suction hose with fluid strainer, by-pass, fluid return hose, and wall mounting adapter. These...

 Open the catalog to page 6

Binks PNEUMATIC DIAPHRAGM PUMP DVP-GEMINI ITEM PART PARTS LIST FOR COMPLETE ASSEMBLY Contact technical support for the list of items available as replacement parts. Listed for reference only—not all items listed are available as replacement parts. ITEM PART (SUPPLIED WITH ITEM 57) BY-PASS TUBE ASSEMBLY (GEMINI PUMP) 62 DVP-56-1 BY-PASS H OS E STAIN LESS STEEL TU BE.. 72 83-2727 ■ GAUGE (0-100 PSI) (BOTTOM MOUNT) ... 74 SSP-8217-ZN UNION SWIVEL 1/4 NPT(m) X 1/4 NPS(f) ... 75 20-4283 UNION SWIVEL 1/2 NPT(m) X 1/2 NPS(f) ... i Replacement glass lens is available - order 83-2290. BEFORE USE : All...

 Open the catalog to page 7

Binks PNEUMATIC DIAPHRAGM PUMP DVP-GEMINI The cleaning frequency depends on material, general operating conditions, and running time. In general, the pump should be cleaned at least once a day, and before a long shut-down, to ensure a long service life. Under no circumstance should paint be allowed to set up, settle out, or dry within the pump. Do not flush pump dry, leave pump under pressure to keep solvent in fluid section. This protects against material hardening. It is advisable to establish a regular cleaning schedule. Clean pump with a solvent appropriate to material 1. Close material valve...

 Open the catalog to page 8

Binks PNEUMATIC DIAPHRAGM PUMP DVP-GEMINI 7. Remove 5 cylinders (33) and 6 "O" Rings (34). 8. Check the condition of the pump body and replace with new components. Assemble in the reverse order. 1. Screw in sleeve (32) on one side, and insert "O Ring" (34) and cylinders (33) in the correct order. Screw in second sleeve (32), and insert slider valve (35) after light greasing with vaseline or oil base grease. 2. Insert pistons (31) complete with seal rings on both sides of body. Note order of assembly. Reassemble nuts (23) and pins (30,46), put the longer pin on air 3. Reassemble steps 1 to 3 in...

 Open the catalog to page 9

Binks PNEUMATIC DIAPHRAGM PUMP DVP-GEMINI 1. Shut off the main air supply and release pressure. Disconnect the main air supply hose assembly from 2. Remove the hose assembly between the regulator (69) 3. Unscrew the 3 thumb screws evenly on the side of cover (51) enough to allow the cover (51) to clear the 4. Remove the cover (51) with the attached DVP Pump (48), Regulator (69) and Agitator with Drive Assembly 5. Loosen the top set screw in the coupling closest to cover (51), to remove coupling with agitator shaft and propeller from agitator motor shaft. 6. Remove the 1" pipe locknut, (turn counter...

 Open the catalog to page 10

All Binks catalogs and brochures

  1. MX1212 Pump System

    24 Pages

    En
  2. MX412 Pump System

    28 Pages

    En
  3. Model 7 Spray Gun

    12 Pages

    En
  4. Trophy Siphon

    80 Pages

    En
  5. Trophy Gravity

    80 Pages

    En
  6. Trophy Pressure

    80 Pages

    En
  7. GEMS 240-5100

    16 Pages

    En
  8. MAG AA Automatic

    8 Pages

    En

Archived catalogs

  1. Trophy series

    10 Pages

    En