MAG AA Automatic - 8 Pages

Add to MyNauticExpo favorites
MAG AA Automatic

Catalog excerpts

(FOR UV HIGH SOLIDS COATINGS) The following instructions provide the necessary information for the proper operation and preventive maintenance of the Binks MAG AA Automatic Manifold Mounted Air- Assisted Airless Spray Gun. Please read and understand all information in this document in order to get the maximum performance from your new MAG AA Automatic spray gun. In the MAG AA Automatic spray gun, the paint or other material to be sprayed is preatomized and forced through the carbide tip by the typical 1,500-3,800 psi fluid pressure (with capabilities preatomizing, the final shaping air supplied by the air cap produces an exceptionally fine and even spray pattern. The result of this spray pattern is an even finish that lends itself to products that need an exceptionally fine finish with reduced overspray and VOC emissions. 20 psi inlet pressure delivers MinVMax. Cylinder Actuating Pressure: Stainless Steel, Aluminum Fluid Path: Stainless Steel Fluid Shut Off Type: Tungsten Carbide Seat (opt.) Outlet Size: Air Inlet Size: Atomizing Air: 1/4" NPT(F) manifold body, 1/4" NPTx manifold body, 1/4" soc head manifold body, 1/8" NPTx Gun Mounting Hole: 1/2" diameter Please be sure to read the uses high pressure to spray paints and solvents. Since liquids sprayed at high pressure can cause injuries, and some paints and solvents can be toxic or cause explosions and fires under certain conditions, your safety and the safety of others depend on your reading the information on this Part Sheet. understand the information presented, call your nearest service representative. Part Sheet

 Open the catalog to page 1

HIGH PRESSURE SPRAY HIGH PRESSURE CAN CAUSE SERIOUS INJURY IF EQUIPMENT IS INSTALLED OR USED READ, UNDERSTAND, AND OBSERVE OPERATE EQUIPMENT ONLY AFTER ALL INSTRUCTIONS ARE CLEARLY UNDERSTOOD. In this part sheet, the words WARNING, CAUTION and NOTE are used to emphasize important safety information as follows: Hazards or unsafe practices which could result in severe personal injury, death or substantial property damage. Hazards or unsafe practices which could result in minor personal injury, product Important installation, operation or maintenance information. INJECTION HAZARD Spray from...

 Open the catalog to page 2

MAG AA AUTOMATIC SPRAY GUN SET-UP INSTRUCTIONS — SPRAY INSTRUCTIONS TO CHANGE FROM COMBINED FAN AND 1. Remove item (31) side port control by turning counter-clockwise with a 9/16 wrench. 2. Install item (32) set screw into thread at the bottom of tapered cavity of where the side port was. 3. Install item (33) side port plug into the upper part of the threaded cavity of where the side port was. 4. Remove item (29) 1/4 npt plug form the fan air port and replace it with item (35) D.M. nipple. Safe connection. Verify that the gun is grounded per the automated machine manufacturer's...

 Open the catalog to page 3

TROUBLESHOOTING DEFECTIVE SPRAY PATTERNS The following procedure summarizes the steps that an operator must immediately take when the first signs of a defective spray pattern emerge. 1. Check the external portion of the fluid tip for material buildup. If buildup has occurred, secure the gun trigger safety switch and clean the gun fluid tip with a non-metal soft brush. 2. If the spray pattern exhibits signs of tails at the top or bottom ends of the pattern, increase the air pressure gradually until the tails disappear. 3. If increasing air pressure does not dissipate the tails, the fluid tip...

 Open the catalog to page 4

MAG AA AUTOMATIC MANIFOLD MOUNTED AIR ASSISTED AIRLESS SPRAY GUN MAINTENANCE/TROUBLESHOOTING AND SERVICE INSTRUCTIONS Disassemble spray gun and remove all o-rings before immersing gun in cleaning solvent. Contact with solvents may induce o-ring swelling beyond their specification sizes and cause Use PTFE (Cooper #540 395) based grease to lubricate all o-rings and moving parts before reassembly into the gun body. To further protect the environment, avoid storing solvents or solvent-soaked wipes, such as those used for surface preparation and cleanup, in open or absorbent containers. Numbers...

 Open the catalog to page 5

MAG AA Automatic MOUNTING SPECIFICATIONS 5 9/16" 1.750 Piston Assembly .966 1/4" O.D. TUBE X 1/8"NPT FITTING CYLINDER AIR Piston Housing 2.700 SIDE PORT AIR FAN ADJUSTMENT 1.282 1.201 1.826 1/4"NPT(F) FAN AIR INLET MAG AA Automatic PISTON POSITIONING PISTON VENT AND FLUID .704 BY-PASS WEEP PORT 1/4"NPT(F) FLUID 1/2" DIA HOLE INLET TYPICAL 1.470 FOR GUN MOUNTING ROD BOTH SIDES SET SCREW FOR ROD MOUNT OR 1/4"NPT(F) SINGLE BOLT ADAPTER MOUNT ATOMIZING AIR INLET 3.158 2.306 .402 OPTIONAL ADAPTER PLATE MOUNTS ARE LISTED ON PAGE 8 Install piston assembly into piston housing. Be sure all o-rings...

 Open the catalog to page 6

MAG AA AUTOMATIC MANIFOLD MOUNTED AIR ASSISTED AIRLESS SPRAY GUN PARTS LIST When ordering, please — Retaining ping (Roto clip E-15-55).. 1 57-13* Optional Setup (Same as 35a) OPTIONAL SETUP: ITEMS 32 (SIDE PORT ASSEMBLY) WHEN Tools provided with spray gun: • Available as part of Rebuild Kit 54-5307. High Performance Seal Kit. A Available as part of Piston Assembly 54-5355. 54-5355 is a part of 54-5315 and is available sparately. ♦ Also available: 20-6750-K10 (Kit of 10 O-rings for AA4 Aircap). m Available as part of 20-6037-K10 Soft Seal Kit (10 rings). * Item Nos. 32, 33 and 35b are...

 Open the catalog to page 7

MAG AA AUTOMATIC MANIFOLD MOUNTED AIR ASSISTED AIRLESS SPRAY GUN REPAIR, CLEANING & MOUNTING KITS 54-4994 Cleaning Kit (provided with gun): includes one standard stiff nylon pipe cleaning brush, full-size nylon brush, tip cleaner, and Binks Gunners Mate Lubricant 54-5303 Standard Performance Seal Kit 54-5307 High Performance Seal Kit FLUID SEATS 54-4960 Standard UHMW Fluid Seat 54-4926 Optional Tungsten Carbide Fluid Seat FLUID FILTER Thin to Medium Materials Medium to Heavy Materials Medium to High Solids 41-4458 PTFE O-ring Lube 54-4997 HVLP Test Gauge AA2 54-5022 HVLP Test Gauge AA4...

 Open the catalog to page 8

All Binks catalogs and brochures

  1. Trophy Siphon

    80 Pages

  2. Trophy Gravity

    80 Pages

  3. Trophy Pressure

    80 Pages

  4. GEMS 240-5100

    16 Pages

Archived catalogs

  1. Trophy series

    10 Pages