Binks MACH 1SL HVLP - 8 Pages

Add to MyNauticExpo favorites
Binks MACH 1SL HVLP
  1. P. 1

  2. P. 2

  3. P. 3

  4. P. 4

  5. P. 5

  6. P. 6

  7. P. 7

  8. P. 8

Catalog excerpts

Binks MACH 1SL HVLP SPRAY GUN Mach 1SLA (Adjustable Fluid Inlet) & Mach 1SLV (Vitreous) The Binks MACH 1SL HVLP Gun is a top quality high performance air spray gun . You only have to pick it up to feel the difference. Its superbly balanced forged aluminum body offers the operator extra comfort and control. All of the gun’s components are machined and finished to exacting tolerances and only the best materials are used, ensuring years of peak efficiency. 4 The MACH 1SL HVLP airspray gun has special nozzles and modifications that allow it to operate at high transfer efficiencies in compliance with the “California South Coast Air Quality Management District” regulations as a “high volume, low pressure” airspray gun. The air inlet passage in the gun body incorporates a venturi which limits airflow. High pressure, low volume airflow is converted to high volume, low pressure at this point. Special air and fluid nozzles enable the gun to atomize fluid at low air pressures and velocities, creating the “soft spray” effect for high transfer efficiencies. To obtain optimum performance from your new MACH 1SL HVLP airspray gun, read all instructions carefully. NOTE 5 1 2 6 3 7 Illustration Key 1. 2. 3. 4. 5. 6. 7. 8. Lightweight Air Nozzle Fluid Inlet 3/8" NPS(m) Extra Smooth Trigger Action Stainless Steel Fluid Nozzle and Needle Side Port Control Fluid Control Knob Forged Aluminum Body Air Inlet 1/4" NPS(m) 8 IMPORTANT REGULATORY NOTE regarding the use of this product appears on page 8. Package Contents Please note that your Binks MACH 1SL HVLP airspray gun package was shipped with the following contents. If anything in the following list is missing, call 1-800-99-BINKS for a prompt shipment to you of the missing item. 1 1 1 1 MACH 1SL Spray Gun Part Sheet . . . . . . . . . . . 2665 Gunners Mate Gun Brush Replaces Part Sheet 77-2665R-5 Part Sheet 77-2665R-6

 Open the catalog to page 1

TYPES OF INSTALLATION CONNECTING GUN TO “PRESSURE ASSISTED” 1 QT. CUP (Figure 1) Oil & Water Extractor PRESSURE TANK WITH 2 REGULATORS (Figure 4) Air pressure for atomization is regulated at the extractor. The flow of the fluid is adjusted by the fluid valve control knob on gun, viscosity of paint and air pressure. Air Supply Air Supply PRESSURE CUP HOOKUP (Figure 2) Air FIG 1 Pressure-Assisted Cup The stainless steel pressure-assisted 1-quart cup utilizes a low pressure air bleed port on the gun head to slightly pressurize the cup and provide fluid flow to the nozzle. A check valve prevents the...

 Open the catalog to page 2

OPERATION AND MAINTENANCE FOR MACH 1SL HVLP SPRAY GUN Your new MACH 1SL HVLP spray gun is exceptionally rugged in construction and is built to stand up under hard, continuous use. However, like any other fine precision instrument, its most efficient operation depends on a knowledge of its construction, operation and maintenance. Properly handled and cared for, it will produce beautiful, uniform finishing results long after other spray guns have worn out. SET-UP FOR SPRAYING Connecting Gun To Air Hose Air should be supplied by a suitable length of 5/16" diameter air hose fitted with a 1/4" NPS(f)...

 Open the catalog to page 3

Binks MACH 1SL, MACH 1SLA (ADJUSTABLE FLUID INLET), AND MACH 1SLV PARTS LIST (When ordering, please specify Part No.) RETAINER RING (Metal). HEAVY DUTY SPRING (Optional) SEAL CARTRIDGE ASSEMBLY ADJUSTABLE FLUID INLET WRENCH (Not Included - Optional) QUICK CHANGE SIDE PORT CONTROL ASSEMBLY FLUID INLET ASSEMBLY (Mach 1SLV). * See Air and Fluid Nozzle Chart on page 5. Included in 54-4278 Spare Parts Kit. Optional - Order separately.

 Open the catalog to page 4

FLUID NOZZLES STANDARD FLUID NOZZLES Use stainless steel fluid needle (54-4382) for all above nozzles. Optional nylon-tipped stainless steel fluid needle (54-4381) is also available. Optimum setup for clear coat spray is 92GS Fluid Nozzle x 96G Air Nozzle Assembly. NEEDLE ADJUSTMENT LENGTH (See adjustment guide at right.) (Needs to be adjusted to fit your gun. See adjustment guide at right.) Adjustment Guide Model Length NOZZLE SIZES SPECIAL PURPOSE NOZZLES Example: 93GS Fluid Nozzle, 92P Low Volume Nozzle for general industrial and automotive fine finish. 95AP High Solids Nozzle for hard to atomize coatings...

 Open the catalog to page 5

FLUID PRESSURE Light Stains, Inks Acrylic Enamels NOZZLE SELECTION * NOTE: Regulator pressures are based on 25' of 5/16" diameter hose in good condition without quick-disconnects or other restrictive fittings. Use the air nozzle test gauge accessory to confirm the atomizing/regulator pressure relationship for your actual air supply set-up. These recommendations are for "typical" or "average" fluids, and are intended to serve as a starting point. Adjust as necessary for your specific application.

 Open the catalog to page 6

SPRAY TECHNIQUE CONTROLLING THE FAN SPRAY The first requirement for a good resultant finish is the proper handling of the gun. The gun should be held perpendicular to the surface being covered and moved parallel with it. The stroke should be started before the trigger is pulled and the trigger should be released before the stroke is ended. This gives accurate control of the gun and fluid. The fan spray is controlled by means of the side port control assembly (7). Turning this control clockwise until it is closed will give a round spray; turning it counterclockwise will widen the spray into a fan...

 Open the catalog to page 7

IMPORTANT REGULATORY NOTE Some regulatory agencies prohibit the operation of HVLP spray guns above 10 psi nozzle atomizing pres- sure. Users subject to this type of regulation should not exceed 10 psi (50 psi gun inlet pressure). See Air Pressure Recommendations, page 6 and General Spray Instructions, page 4. It is recommended that the nozzle test gauge (see below) be used to confirm actual nozzle operating pressure. It may also be a requirement of some regulatory agencies that users have this gauge nozzle available on site to verify that the gun is being operated within the limits of applicable...

 Open the catalog to page 8

All Binks catalogs and brochures

  1. MX1212 Pump System

    24 Pages

    En
  2. MX412 Pump System

    28 Pages

    En
  3. Model 7 Spray Gun

    12 Pages

    En
  4. Trophy Siphon

    80 Pages

    En
  5. Trophy Gravity

    80 Pages

    En
  6. Trophy Pressure

    80 Pages

    En
  7. GEMS 240-5100

    16 Pages

    En
  8. MAG AA Automatic

    8 Pages

    En

Archived catalogs

  1. Trophy series

    10 Pages

    En