84501X High Pressure Material Regulator - 8 Pages

Add to MyNauticExpo favorites
84501X High Pressure Material Regulator
  1. P. 1

  2. P. 2

  3. P. 3

  4. P. 4

  5. P. 5

  6. P. 6

  7. P. 7

  8. P. 8

Catalog excerpts

INCLUDING: OPERATION, INSTALLATION & MAINTENANCE RELEASED: 8-20-99 HIGH PRESSURE (REVF) MATERIAL REGULATOR READ THIS MANUAL CAREFULLY BEFORE INSTALLING, OPERATING OR SERVICING THIS EQUIPMENT. It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference. SERVICE KITS Use only genuine Bink's replacement parts to assure compatible pres- sure rating and longest service life. 863001 valve kit for seat replacement on models 845012 (see page 4). 863005 valve kit for ball and seat replacement on models 845013 (see 863007 valve kit for ball and seat replacement on models 845010, 863008 diaphragm kit for replacement of diaphragms (see page 4). 863013 rebuild kit for general repair of the 845010,845011 and 845014 regulators. This includes an 863008 diaphragm kit and an 863007 863014 rebuild kit for general repair of the 845012 regulators. This in- cludes an 863008 diaphragm kit and an 863001 valve kit. 863015 rebuild kit for general repair of the 845013 regulators. This in- cludes an 863008 diaphragm kit and an 863005 valve kit. Body Material Ball Size PERFORMANCE DATA Regulated Pressure Range with Maximum Regulated Pressure Maximum Inlet Pressure North American Office International Office ITW Industrial Finishing ITW Industrial Finishing 195 Internationale Blvd Ringwood Road, Bournemouth Glendale Heights, IL 60139 Dorset, BH11 9LH, England

 Open the catalog to page 1

OPERATING AND SAFETY PRECAUTIONS STATIC SPARK HAZARDOUS MATERIALS HAZARDOUS PRESSURE Read and heed all Warnings and Safety Precautions before op- eration of this unit. Use only genuine Bink's replacement parts to assure compat- ible pressure rating and longest service life. Be certain anyone operating this equipment or fluid system has been trained to use it safely. HIGH PRESSURE DEVICE. IMPROPER USAGE OF THIS EQUIPMENT COULD RESULT IN SERIOUS INJURY. The possibility of injection into the flesh is a potential hazard. Wear approved safety glasses or face shield and other equip- ment as needed to...

 Open the catalog to page 2

OPERATING INSTRUCTIONS TROUBLE SHOOTING Refer to pages 4 and 5 for parts reference. • To INCREASE outlet pressure, turn the (6) adjusting screw CLOCK- • To DECREASE outlet pressure, turn the (6) adjusting screw COUN- NOTE: (20) 3/8" Allen wrench is included to make necessary pressure FLUSH-OUT FEATURE FOR DOWNSTREAM MODELS ONLY (see • Flush the regulator periodically. The interval may vary depending on the amount and type of material used. • By using a wrench and "flush-out" plug (provided), the operator is able to move the entire spindle downward and force the ball off the seat, which should...

 Open the catalog to page 3

PARTS LIST / 84501X REGULATOR 863001 Valve Kits include: 863005 Valve Kits include: 863007 Valve Kits include: 863008 Diaphragm Repair Kits include: 863013 Rebuild Kits include: 863014 Rebuild Kits include: 863015 Rebuild Kits include:

 Open the catalog to page 4

PARTS LIST / 84501X REGULATOR . TORQUE REQUIREMENTS , NOTE: DO NOT OVERTIGHTEN FASTENERS. (2) Torque alternately. 1.) Snug. 2.) 20 - 25 ft lbs (27.1 - 33.9 Nm). (10) 65 - 75 in. lbs (7.3 - 8.5 Nm). (14) Torque alternately. 1.) Snug. 2.) 20 - 25 ft lbs (27.1 - 33.9 Nm). 3.) 50 - 55 ft lbs (67.8 - 74.6 Nm). ¡ © ¢ £ 1 4 2 5 UPPER REGULATOR SECTION LUBRICATION - SEALANTS - 7 Apply Dri-Slide upon assembly. Apply Loctite nickel anti-seize to threads. Apply clutch grease. Apply Loctite 242 to threads. 3 6 8 MATERIAL CODE [A] = Aluminum [C] = Carbon Steel [H] = Hytrel [SS] = Stainless Steel [T] = PTFE...

 Open the catalog to page 5

_REGULATOR DISASSEMBLY FOR "WARNINGS", REFER TO "OPERATING AND SAFETY PRE- CAUTIONS" ON PAGE 2 FOR DETAILS. BEFORE SERVICING, READ "WARNING: DISASSEMBLY HAZ- TOOLS REQUIRED: Small bench vise, 3/8" alien wrench (included), 5/32 alien wrench, torque wrench and Loctite 242. NOTE: It is not always necessary to remove the regulator from the fluid line to service or inspect only the valve section. BEFORE DOING ANY IN-LINE SERVICE, ALL FLUID PRESSURE MUST BE RELIEVED. HEED ALL WARNINGS FOUND ON PAGE 2. ALLEN WRENCH NOTE: The 3/8" alien wrench is included and can be used for several functions including:...

 Open the catalog to page 6

DIMENSIONAL DATA 3.218” 1/4” - 20 UNC 2B (81.7 mm) 2.312” (59 mm) 7.827” FLOW DIRECTION MARKING (198.8 mm) BOTTOM VIEW ‘‘C” and ‘‘D” thread = 3/8 - 18 N.P.T.F. ‘‘D” ‘‘C” 1.686” 1.093” (42.8 mm) (27.8 mm) NOTE: S 845010, 845011, 845013 and 845014 (downstream models) “C” is the INLET port, “D” is the OUTLET port. S 845012 (back pressure models) “D” is the INLET port, “C” is the OUTLET port. FIGURE 7 OPTIONAL ACCESSORIES GAUGE AND AUXILIARY PORT 873056 Outlet Adapter 3/8 - 18 N.P.T.F. - 1 873054 873055 84501X Rear Mount Gauge 0 - 5000 p.s.i. Stainless Steel 0 - 3000 p.s.i. Stainless Steel PAGE 7...

 Open the catalog to page 7

All Binks catalogs and brochures

  1. MX1212 Pump System

    24 Pages

    En
  2. MX412 Pump System

    28 Pages

    En
  3. Model 7 Spray Gun

    12 Pages

    En
  4. Trophy Siphon

    80 Pages

    En
  5. Trophy Gravity

    80 Pages

    En
  6. Trophy Pressure

    80 Pages

    En
  7. GEMS 240-5100

    16 Pages

    En
  8. MAG AA Automatic

    8 Pages

    En

Archived catalogs

  1. Trophy series

    10 Pages

    En