43P Gun Airless Gun - 8 Pages

Add to MyNauticExpo favorites
43P Gun Airless Gun
  1. P. 1

  2. P. 2

  3. P. 3

  4. P. 4

  5. P. 5

  6. P. 6

  7. P. 7

  8. P. 8

Catalog excerpts

The Binks Model 43P is a low to medium-volume plural component (spray and/or pour) dispensing device designed specifically for plural component systems. Capacity is up to 20 lbs. spray using a patented static mixing principle. The 43P, and its companion the 43PA (automatic), uses the opposed internal orifices principle with no moving parts (patented). Spray patterns are by nozzle selection. Gun output is dependent upon nozzle and impingement orifices in conjunction with applied fluid pressures. Impingement orifices usually are matched but may be dissimilar to "balance" divergent viscosities and/or ratios. The 18-8 stainless steel head is designed with cross- drilled ports for ease of maintenance. The ports allow access to remove impacted cured resins. Immersion in solvent will not affect the seals. Both resin (1/4 NPS) ports have check valves. The needle valves share common parts (springs, housing, take-up nuts, packings and followers) for simplicity. The resin needles are ball type, the purge is tapered tip. The rugged forged aluminum gun handle is anodized for corrosion resistance. The trigger's finger geometry affords comfortable trigger pull and operation. Part Sheet

 Open the catalog to page 1

In this part sheet, the words WARNING, CAUTION and NOTE are used to emphasize important safety information as follows: Hazards or unsafe practices which could result in severe personal injury, death or substantial property damage. Hazards or unsafe practices which could result in minor personal injury, product Important installation, operation or maintenance information. Read the following warnings before using this equipment. Before operating finishing equipment, read and understand all safety, operation and maintenance information provided in the operation manual. WEAR SAFETY GLASSES Failure...

 Open the catalog to page 2

Binks MODEL 102-1700 (43P) AIRLESS SPRAY GUN Your Binks 43P Airless Spray Gun has been thoroughly tested before leaving the factory. No adjustment is required prior to its operation other than installing the Hook up solvent line and check to insure proper purg- ing. Open purge valve and allow solvent to enter the gun head. Activate valve on-off and observe solvent spray emitting from front of gun. It is important that solvent purge be available in case of incorrect resin- hardener hook-up, reacting fluids, or mixed resins Remove Items 1, 2, 3, and 5. Connect material lines to gun. Run system to...

 Open the catalog to page 3

MAINTENANCE INSTRUCTIONS A. Short Period Shut-down. When stopping operation of the Model 43P gun for short periods exceeding 1/2 hour, remove nut (1), nozzle tip (2), gasket (3), and any washers from gun, and soak them in a clean solvent. 2. Inspect inside of mix chamber (8) and clean thoroughly. 3. Prior to reassembly, blow tip and washers with compressed B. Long Period Shut-down. 1. For overnight or longer periods of down-time, it is recom- mended that items 1, 2, 3, (two) plugs (5) and (two) orifices (6) be removed and placed in a clean solvent. 2. Hold gun over empty container. Rotate knob...

 Open the catalog to page 5

This product is covered by Binks' 1 Year Limited Warranty. Binks Worldwide Sales and Service Listing: www.binks.com Binks has authorized distributors throughout the world. For technical assistance or the distributor nearest you, see listing below. U.S./Canada Technical Service Office: 195 Internationale Blvd., Glendale Heights, IL 60139 Toll-Free Telephone: 1-888-992-4657 (U.S.A. and Canada only) An Illinois Tool Works Company 5/07 ©2007 Illinois Tool Works Inc. All rights reserved. Printed in U.S.A. 77-1722R-11 Revisions: (P1) Corrected model number; (P4) Removed Part No. 19 from exploded view;...

 Open the catalog to page 8

All Binks catalogs and brochures

  1. MX1212 Pump System

    24 Pages

    En
  2. MX412 Pump System

    28 Pages

    En
  3. Model 7 Spray Gun

    12 Pages

    En
  4. Trophy Siphon

    80 Pages

    En
  5. Trophy Gravity

    80 Pages

    En
  6. Trophy Pressure

    80 Pages

    En
  7. GEMS 240-5100

    16 Pages

    En
  8. MAG AA Automatic

    8 Pages

    En

Archived catalogs

  1. Trophy series

    10 Pages

    En