41-12303 B8 Air Motor - 12 Pages

Add to MyNauticExpo favorites
41-12303 B8 Air Motor

Catalog excerpts

Your new Binks B8 is an 8" diameter, 5" stroke air motor designed to operate at from 20 to 90 PSI air pressure (maximum). The B8 features an easy to maintain air slide valve with lubricated Derlin seals and quiet exhaust. Use the lowest air pressure setting which gives proper atomization of the fluid at the spray gun tip. Excessive pressure only causes undue wear to the equipment. WARNING — HIGH PRESSURE — WARNING When driving a high pressure fluid section, this air motor can produce fluid pressures of over 3000 PSI. • FLUID UNDER HIGH PRESSURE CAN PENETRATE THE SKIN AND CAUSE SEVERE INTERNAL INJURY • IN CASE OF INJURY OBTAIN MEDICAL ATTENTION IMMEDIATELY • BE SURE TO REPORT NATURE OF INJURY AND TYPE OF FLUID OR SOLVENT TO THE DOCTOR Be sure you understand ALL of the following instruc- tions thoroughly BEFORE operating any part of the air- less equipment system. CONSULT YOUR BINKS REPRESENTATIVE TO CLEAR UP ANY ITEMS OF 1. All Binks high pressure airless pumps should be GROUNDED to avoid DANGEROUS STATIC SPARKING, EXPLOSION, or FIRE when SPRAY- a. Be sure object being sprayed is GROUNDED. 2. NEVER clean, change, or remove the nozzle from the spray gun without first doing the following: a. Be sure to set the trigger safety on the gun. b. Shut off pump. Release fluid pressure in the entire system, from pump to spray gun, by opening the PRESSURE RELIEF VALVE. With the airless system inactivated as described above, all worn or defective parts should be replaced or repaired BEFORE restarting the system. 3. NEVER remove the fluid hose or spray gun from the system without first releasing the system pressure (see instructions a and b under paragraph 2, above). Remember, the fluid may be under very high pres- sure (3000 pounds per square inch or more). 4. NEVER trigger the spray gun to release system pres- sure: USE PRESSURE RELEASE VALVE (see 5. NEVER handle the spray gun carelessly. 6. Never allow the gun's spray to come close to any part of the human body, even when the spray nozzle 7. NEVER plug a hose leak with your finger, with adhesive tape, or other "stop-gap" devices. 8. NEVER operate the airless system with a defective hose. ALWAYS replace the defective hose immedi- 9. BEFORE doing ANY maintenance work on the pump, hose, or spray gun, or BEFORE leaving the airless equipment system unattended for ANY length of time, or BEFORE shutting down the sys- tem, BE SURE TO FOLLOW PROCEDURE 10. NEVER spray flammable liquids in the vicinity of: a. ANY open flame, lighted cigarettes, etc. b. ANY electrical apparatus that is operating. 11. NEVER spray flammable solvent through the gun nozzle tip. To do so generates static electricity and could cause static sparking with subsequent explo- sion or fire (see paragraph 1). ALWAYS remove the nozzle tip from the spray gun BEFORE cleaning the tip or "solvent flush" cleaning the gun (see 12. Binks airless pumps can develop hydraulic pressure of 3000 pounds per square inch or more. All of the components incorporated into the pump, spray gun, and the other elements of the airless system, have been carefully designed and tested to ensure their safe operation under these high pressures, WHEN PROPERLY HANDLED AND MAINTAINED. For continuing safety, users are urged to: a. ALWAYS handle carefully all hose connections, joints, and seating surfaces on the spray gun to prevent damage. b. NEVER kink or bend the fluid hose into less than a four inch radius. c. FREQUENTLY check the hose for kinks or abrasions. These may develop into a rupture. d. NEVER use standard hardware to modify the airless system. ALWAYS use Binks high pres- sure fittings only. Replaces Part Part Sheet Sheet

 Open the catalog to page 1

In this part sheet, the words WARNING, CAUTION and NOTE are used to emphasize important safety information as follows: Hazards or unsafe practices which could result in severe personal injury, death or substantial property damage. Hazards or unsafe practices which could result in minor personal injury, product Important installation, operation or maintenance information. Read the following warnings before using this equipment. Before operating finishing equipment, read and understand all safety, operation and maintenance information provided in the operation manual. WEAR SAFETY GLASSES...

 Open the catalog to page 2

Binks MODEL 41-12303 B8 AIR MOTOR See High Pressure Warning Statement on Front Cover 1. Disconnect air supply line to the air motor and remove the inlet fitting (1), inlet seal (2), and 3. Remove four screws (6A) which hold the cover (5) and static ground wire assembly (6B) to the motor base assembly (7). 4. Carefully remove the cover assembly (5). The inside of the cover assembly is lined with "Soundfoam" and may be damaged if scraped. This Side Shown TO REMOVE AND DISASSEMBLE VALVE 1. Using an adjustable wrench, loosen and remove the roller spring retainer assemblies (13). 2. The push rod...

 Open the catalog to page 3

This Side Shown TO INSPECT THE SLIDE VALVE 1. Remove two bolts (18C) and toothwashers (18B) and remove the inlet manifold assembly (18A). The transfer tube (19) may or may not come out of the inlet manifold assembly. An o-ring holds the transfer tube in place. 2. Lift off the transfer manifold assembly (16). Check the o-ring (27) under the transfer manifold. 3. Using two adjustable wrenches, remove the trip rod nuts (23B) and (23A) and also nut seal (22) from atop the slide valve (17). It will be necessary to pull the trip rod assembly (26) up a little in order to engage the flats on 4....

 Open the catalog to page 4

Packing Assembly TO INSPECT THE TRIP ROD ASSEMBLY 1. Check the trip rod assembly (26) for straightness. The assembly is made up of the trip rod (41 A), spring (42), two trip spring guides (43), retainer nut (44A), safety nut (44B), and a short length of 18 gauge safety wire 2. To dissassemble, remove safety wire (44C) and, with adjustable wrenches on the trip rod flats, remove nuts 3. To remove piston rod seals (55) thru (59), pull piston rod (39) straight DOWN and out of motor base assem- bly (7), remove screws (61) and plate (60). Packing 4. Piston rod seal (45) may also be removed.

 Open the catalog to page 5

All Binks catalogs and brochures

  1. Trophy Siphon

    80 Pages

  2. Trophy Gravity

    80 Pages

  3. Trophy Pressure

    80 Pages

  4. GEMS 240-5100

    16 Pages

Archived catalogs

  1. Trophy series

    10 Pages