21, 21V & 21M Automatic Spray Gun - 28 Pages

Add to MyNauticExpo favorites
21, 21V & 21M Automatic Spray Gun
  1. P. 1

  2. P. 2

  3. P. 3

  4. P. 4

  5. P. 5

  6. P. 6

  7. P. 7

  8. P. 8

  9. P. 9

  10. P. 10

  11. P. 20

Catalog excerpts

SERVICE MANUAL BRASS BODY The following instructions provide the necessary information for the proper operation and preventive maintenance of the Binks Model 21 Automatic Spray Gun. Please read and understand all information in this document in order to get the maximum performance from your new Model 21 spray gun. All Model 21 spray guns feature nickel plated brass air caps and bodies that will withstand years of use under the toughest conditions. The Model 21V spray guns contain tungsten carbide fluid nozzles and needles for use with abrasive fluids. The Model 21M spray guns are internal mix spray guns used in line striping. The Model 21 Series of spray guns are heavy duty, pneumatically operated, automatic spray guns with forged brass bodies. PROP 65 WARNING WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. SPECIFICATIONS: Maximum Fluid Pressure: 100 psi /6.9 bar Gun Body: Plated Brass It is the customer's responsibility to have all operators and service personnel read and understand this manual. Fluid Path: Brass / Electroless Nickle Plated Fluid Inlet Size: 3/8" NPS(m) Thread Air Inlet Size: Contact your local Binks representative for additional copies of this manual. Mounting Hole: 1/2" Mounting Bracket: 54-380 (1/2" Bar) READ ALL INSTRUCTIONS BEFORE OPERATING THIS BINKS PRODUCT 77-2976-R3.2 (8/2015)

 Open the catalog to page 1

EN In this part sheet, the words WARNING, CAUTION and NOTE are used to emphasize important safety information as follows: Hazards or unsafe practices which could result in severe personal injury, death or substantial property damage. Hazards or unsafe practices which could result in minor personal injury, product or property damage. NOTE Important installation, operation or maintenance information. Read the following warnings before using this equipment. READ THE MANUAL Before operating finishing equipment, read and understand all safety, operation and maintenance information provided in the operation...

 Open the catalog to page 2

EN BINKS MODEL 21 & 21V SERIES AUTOMATIC SPRAY GUN HOOK-UP 1. ir pressure of 35-50 PSI minimum required for A cylinder operation. 2. or rapid operation, the air line between three-way F valve and the cylinder operating air connection should be as short as possible. 3. ll air supplied to the gun should be dirt and moistureA free. A DeVilbiss centrifugal air filter mounted in the air supply line is recommended. 4. f the gun is to stand idle for any length of time, shut I off. This will prevent small leaks throughout the system from turning on the gun. The points that require lubrication on this...

 Open the catalog to page 3

EN BINKS MODEL 21 & 21V SERIES AUTOMATIC SPRAY GUN BINKS MODEL 21 SOLVENT FLUSH LINE Fluid Cylinder Air ATOMIZING AIR SUPPLY Shut-Off Cocks Mounting Lockscrew THREE WAY VALVE OR TRIGGERING DEVICE Side Port Control Atomizing Air COMPRESSED AIR (From Extractor) SUPPLY FLUID SUPPLY Fluid Adjustment Control 3-Way Valve Cylinder Air (From Extractor) For multiple gun installation, a fluid manifold may be used. Fluid adjustments are made using the fluid control screw on PRESSURE TANK each gun. However, when precise fluid control is necessary, a fluid regulator for each gun must be used. SOLVENT FLUSH...

 Open the catalog to page 4

EN BINKS MODEL 21 & 21V SERIES AUTOMATIC SPRAY GUN PARTS LIST When ordering, please specify Part No. ITEM NO. ❍ When ordering, please specify number stamped on nozzle. ■ hen ordering, please specify gun model and number stamped on needle. W • Parts also available in Repair Kit 6-191. ✩ llows for easy gun change while A maintaining gun alignment. Gun wrench, 5-476 is recommended for removing fluid nozzle. Please order separately. ● Includes Item 34.

 Open the catalog to page 5

EN BINKS MODEL 21 & 21V SERIES AUTOMATIC SPRAY GUN AIR CAP ORDERING GUIDE AIR CAP MARKING ORDER PART NUMBER ORDER PART NUMBER FLUID NOZZLE AND NEEDLE ORDERING GUIDE FLUID NOZZLE MARKING ORDER PART NUMBER NEEDLE MARKING ORDER NEEDLE NUMBER ORIFICE SIZE INCHES (MM) Stainless Steel Stainless Steel Stainless Steel Stainless Steel Stainless Steel Stainless Steel Tungsten Carbide Tungsten Carbide Tungsten Carbide INTERNAL MIX HEAVY MATERIAL NOZZLES (OPTIONAL) FLUID NOZZLE* 59ASS, 59BSS, 59CSS NOZZLE BASE WITH RING 54-372 54-1584 AIR NOZZLE ASSEMBLY* NOZZLE TIP* NITRALLOY 200 * hen ordering please specify...

 Open the catalog to page 6

EN MODEL 21 NOZZLE AND NEEDLE SELECTION CHARTS FLUID X AIR TYPE OF FLUID TO BE SPRAYED NOZZLES 63BSS X 63PB 66SS X 66SD THIN, 5-25 CENTIPOISE 63BSS X 21MD-1 wash primers, dyes, stains, solvents, water, inks, sealers, laquers, lubricants, 63CVT X 66PH zinc chromates, acrylics 66SS X 66SK 63BSS X 200 63BSS X 63PB 66SS X 66SD MEDIUM, 25-70 CENTIPOISE 63BSS X 21MD-1 synthetic enamels, varnishes, shellacs, 63BSS X 21MD-3 fillers, primers, epoxies, urethanes, 67VT X 21MD-2 lubricants, wax emulsions, enamels 63CVT X 66PH 67VT X 67PB 66SS X 66SK 63BSS X 21MD-1 63BSS X 21MD-3 68SS X 709SS HEAVY, 70-115...

 Open the catalog to page 7

BINKS MODEL 21M AUTOMATIC SPRAY GUN (6219-8219-1) The Binks Model 21M is designed to deal with rough environments both inside and outside the spray gun. The Binks 21M spray gun will stand up to any line striping process. The internal mix air cap keeps the spray pattern precise while the quick actuating air valve ensures material is only sprayed where and when you want it. The standard model includes a 0.281" orifice for heavy viscosity materials and an air cap that sprays up to a 7" pattern. The Model 21M has the capability to quick flush the air and fluid nozzles, making it perfect for line striping...

 Open the catalog to page 8

EN BINKS MODEL 21M (BRASS BODY) AUTOMATIC ROADMARKING SPRAY GUN 12 PARTS LIST When ordering, please specify Part No. ITEM NO. Part of 54-496 packing box assembly. Includes Item 33. Gun Wrench 5-476 is recommended for removing fluid nozzle. Please order separately. ✩ llows for easy gun change while A maintaining gun alignment. No repair kit available. Please order parts separately.

 Open the catalog to page 9

PISTOLA PULVERIZADORA AUTOMÁTICA BINKS MODELOS 21, 21V, Y 21M (6220-XXXX-X) (6235-XXXX-X) (6219-XXXX-X) Las siguientes instrucciones proporcionan la información necesaria para la operación adecuada y el mantenimiento preventivo de la pistola pulverizadora automática Binks modelo 21. Sírvase leer y entender toda la información contenida en este documento para lograr el máximo rendimiento de su nueva pistola pulverizadora modelo 21. casquillos de aire de latón niquelado para soportar muchos años de uso ante las más duras condiciones. Las pistolas pulverizadoras modelo 21V tienen boquillas y agujas...

 Open the catalog to page 10

All Binks catalogs and brochures

  1. MX1212 Pump System

    24 Pages

    En
  2. MX412 Pump System

    28 Pages

    En
  3. Model 7 Spray Gun

    12 Pages

    En
  4. Trophy Siphon

    80 Pages

    En
  5. Trophy Gravity

    80 Pages

    En
  6. Trophy Pressure

    80 Pages

    En
  7. GEMS 240-5100

    16 Pages

    En
  8. MAG AA Automatic

    8 Pages

    En

Archived catalogs

  1. Trophy series

    10 Pages

    En