video corpo

CONVEX MTH18240
12Pages

{{requestButtons}}

Catalog excerpts

CONVEX MTH18240 - 1

Operating Instructions

Open the catalog to page 1
CONVEX MTH18240 - 3

The CONVEX series underwater lights are designed to use the latest LED lighting The thru-hull designed casings enable very simple installation on the hull without making any bigger holes through the hull under water All the models are available in aluminium bronze casings. The lighting is available in white, blue or green colors or three-color. All the models are designed with 18 power LEDs and suitable power supply units. * Aluminium Bronze Casing * 18 Power LEDs Design * White, Blue, Green or Three-Color Lighting • Tempered Glass Optical Window • High-Efficiency Lens * Over-Temperature...

Open the catalog to page 3
CONVEX MTH18240 - 4

Underwater Light CONVEX MTH18240 The 6 mm depth tempered glass optical window. (2) Underwater light casing Aluminium bronze casing with M24 fixing screw and cable gland. The M24 stainless-steel nuts with locking and bonding screws and washer. The 8-pole multi-core cable to connect the power supply unit.

Open the catalog to page 4
CONVEX MTH18240 - 5

Power Supply Unit MPS06800 Terminal-block connector to connect optional remote control unit or switch. Terminal-block connector to connect the LED underwater light using 8-pole multi-core cable. Terminal-block connector to connect l2-24Vdc power supply. Terminal-block connector to connect to the DC IN connector of another power supply unit.

Open the catalog to page 5
CONVEX MTH18240 - 6

The underwater light kit consists of the following components: • Underwater Light CONVEX MTH18240 • Power Supply Unit MPS06800 • Locking nut M24 with locking screw M8 and bonding screw M4 * Operating Instructions with Declaration of Conformity and Warranty conditions Underwater Light CONVEX MTH18240 The CONVEX MTH18240 has to be installed on a flat surface on the stern of the hull of the vessel. Do not try to install the underwater light while the vessel is in the water. When the installation is finished briefly test the underwater light prior to launching the vessel. The installation have...

Open the catalog to page 6
CONVEX MTH18240 - 7

The underwater light has to be inserted through the hole from outside of the hull and has to be fixed with the fixing nut M24. Then the locking nut M24 (with locking screw M8 and bonding screw M4) has to be fitted and locked with locking screw M8. • To install the underwater light on the steel hull it is highly recommended to use the optional isolation board (not included) between the hull and underwater light casing to prevent galvanic corrosion. • Do not overtighten the nuts and screws as this can result in hull or underwater light The underwater light has to be connected to the vessels...

Open the catalog to page 7
CONVEX MTH18240 - 8

• The main DC power supply of the vessel has to be switched off before installation. Power supply connection The power supply has to be connected through the switch (not included) and protected by a fuse (not included) to the DC IN terminal-block connector with correct polarity. The power supply voltage has to A power supply unit of another underwater light can be connected to the DC OUT terminal-block • Only one additional power supply unit of the same model number can be connected to the DC OUT terminal-block connector and suitable power supply cable should be used. The appurtenant cap...

Open the catalog to page 8
CONVEX MTH18240 - 9

TECHNICAL SPECIFICATIONS Power requirement Lens angle Optical window Luminous flux White color temperature Operating temperature 6 mm depth tempered glass Power Supply Unit MPS06800 Input voltage Operating temperature Design and specifications subject to change without notice.

Open the catalog to page 9
CONVEX MTH18240 - 10

"l.The equipment manufactured by ASTEL d.o.o. is warranted to be free from defects in workmanship and materials under normal use and service. 2. This Warranty is in effect for of two years from the date of purchase by the user. Proof of purchase must be included, to establish that it is inside the warranty period. 3. This Warranty is transferrable and covers the product for the specified time period. 4. In case any part od the equipment proves to be defective, other than those parts excluded in paragraph 5 below, the owner should do the following: (a) prepare a detailed written statement of...

Open the catalog to page 10
CONVEX MTH18240 - 11

Manufacturer's Name: ASTEL, Podjetje za projektiranje, proizvodnjo in Manufacturer's Address: Dutovlje 138 declares that the products Item, Product Name and Model Number: 1. Underwater Light CONVEX MTH18240 with Power Supply Unit MPS06800 conform to the following Product Specifications: Supplementary Information: The products herewith comply with the requirements of the following Directives and carry the CE- marking accordingly:

Open the catalog to page 11
CONVEX MTH18240 - 12

ASTEL d.o.o., Dutovlje 138, 6221 Dutovlje, Slovenia E-mail: info@astel-marine.com

Open the catalog to page 12

All ASTEL MARINE catalogs and brochures

  1. CONVEX MSR0680

    12 Pages

  2. CONUS MSR0680

    12 Pages

  3. CONUS MST18240

    12 Pages

  4. ARCUS MRM01

    12 Pages

  5. CONUS MSR18240

    12 Pages

  6. PLAQUE MFM0680

    12 Pages

  7. CONVEX MST0680

    12 Pages

  8. CONUS MST0680

    12 Pages

Archived catalogs

  1. Brochure 2013

    21 Pages

  2. CONVEX MTH0680

    12 Pages