CHIRP Thru Hull 6-page Brochure - 6 Pages

Add to MyNauticExpo favorites
CHIRP Thru Hull 6-page Brochure

Catalog excerpts

Broadband / CHIRP Transducers Technical Information When Your Living Depends on Finding Fish... Advantages of Thru-Hull Transducers Rely on Airmar’s new broadband transducers for the ultimate fishing mission. Whether you’re a commercial fisherman, charter captain, or tournament angler, there’s a new game in town! CHIRP transducers enable bottom detection down to 3,000 m (10,000’) with 5 to 10 times greater detail and resolution so precise it’s possible to distinguish between individual baitfish, game fish, and underwater structures. One transducer delivers up to 117 kHz of total bandwidth in just one installation, saving customers time and money. Best performance, minimal drag, designed for larger boats, works with any hull material. Airmar…it’s what’s under your boat. The CHIRP Difference Traditional marine fishfinders operate at discrete frequencies such as 50 kHz and 200 kHz, use relatively short-duration transmit pulses, and use narrowband sonar transducers. In contrast, CHIRP (compressed high-intensity radar pulse) uses a precise sweep pattern of many frequencies within a long-duration transmit pulse from a broadband transducer, so the equivalent sound energy transmitted into the water is 10 to 1,000 times greater than a conventional marine fishfinder. The echo energy returning to the transducer, superior to that generated by a conventional transducer, is then processed by the fishfinder’s DSP (digital signal processing) computer and displayed in ultra-sharp detail on the display. The combination of CHIRP a broadband transducer, , and the fishfinder’s DSP results in dramatically better fish and bottom detection, superior depth capability, and , significantly better performance at speed. Does YOUR Fishfinder CHIRP? Only CHIRP/Spread Spectrum sounders using Airmar broadband transducers can operate as a CHIRP fishfinder system. When Airmar’s new transducer is paired with a broadband fishfinder, the result is 5 to 10 times greater sensitivity and performance than current fishfinder technology. Packed with exclusive technology like Transducer ID® and newly engineered piezoceramic elements, Airmar transducers are über sensitive and designed to automatically sweep frequency bands from 28 kHz to 210 kHz with no tuning necessary. As a result, all targets detected in the entire bandwidth will be seen on the display rather than only what is identified in traditional frequencies at 50 kHz and 200 kHz. When external thru-hull transducers are installed with a High-Performance Fairing, the transducer face is parallel to the waterline resulting in a beam that is vertically oriented for maximum echo returns and the best possible performance. The fairing compensates for hull deadrise and reduces turbulence over the transducer face, which allows tracking at speeds over 30 knots (35 MPH). This installation, when mounted in “clean water” (forward of propellers and running gear), produces the most effective signal return since nothing on the vessel interferes with the transducer’s active surface. Thru-hull transducers will work with any engine type: inboard, outboard, or I/O. Unique Transducer ID® Airmar’s Transducer ID feature measures and stores the operating parameters for each transducer. This enables the fishfinder to automatically configure itself to the transducer being used. The embedded microcontroller continuously monitors ceramic operating temperatures inside the transducer, enabling closed loop control of power output. The transducer’s profile can be presented on the display showing beamwidth coverage as a function of frequency. Stored data also assists with troubleshooting, warranty or any required information about the transducer. Quality “Q” Value Q is a measure of bandwidth and the rise and fall times of target echoes. Airmar Q values range from 1.6 to 30, depending on the model. Competitive transducers have an average Q of 25 to 30. The lower the “Q” number, the less ringing in the transducer and the better the performance—improved individual fish separation along with bottom imaging in rapidly changing water depths such as ledges and offshore canyons. The CHIRP Broadband transducer has a flat response and can run across the entire frequency range. The Non-Broadband transducer peaks its performance at 200 kHz and drops off sharply at frequencies before and after. • Superior performance in noisy environments • Improved bottom tracking at high boat speeds DEEPER. BROADER. GING TECHNOL AN GAME CH Blue Marlin • Precise separation between baitfish and game fish See Theory of Operation for a complete understanding of transducer terminology and operation. www.airmar.com Frequency (kHz) CHIRP Broadband All roundtrip sensitivity data is based on the Figure of Merit (FOM) and the transducer bandwidth relative to the B45 model. **Commonly used non-CHIRP transducers. www.airmar.com ©Airmar Technology Corporation • 10 to 1,000 times more energy on targets Roundtrip Sensitivity* LF HF 1 times 1 times 250 times 50 times 1,000 times 120 times 4,100 times 225 times 6,100 times 240 times Incredible resolution at high-frequency. CHIRP TECHNOLOGY • 5 to 10 times greater detail and resolution All Airmar CHIRP transducers have a Q of 3 or less. Operation with High-Frequency CHIRP Mode. See Guide to Transducer Technology to compare Thru-Hull, In-Hull, Pocket / Keel-Mount, and Transom-Mount options. www.airmar.com Airmar’s complete line of twenty-four (24) CHIRP transducers are available in seven (7) different mounting options to accommodate almost any hull design. CHIRP transducers are available at Gemeco Marine Accessories www.gemeco.com and Airmar EMEA www.airmar.com/emea. Visit www.AIRMAR.com for a list of CHIRP-ready transducers. Transmit Voltage Response (TVR) ine ! ng Mach cer. indi s Fishf roadband transdu ri o u o a Se AIRMAR b er t ound use of an S Your ith the e grad sible w U p p os Only Screen shot courtesy of Jason Pipe IGFA Ambassador Captain. As Airmar constantly improves its products, all specifications are subject to change without notice. All Airmar products are designed to provide high levels of accuracy and reliability, however they should only be used as aids to navigation and not as a replacement for traditional navigation aids and techniques. Xducer ID® is a registered trademark of Airmar Technology Corporation. Other company or product names mentioned in this document may be trademarks or registered trademarks of their respective companies, which are not affiliated with Airmar. Thru-Hull Screen shot courtesy of Garmin®.

 Open the catalog to page 1

All Airmar catalogs and brochures

  1. B258 Thru-Hull

    2 Pages

  2. In-Hull Chirp

    6 Pages

  3. Thru Hull Chirp

    6 Pages

  4. HT200

    2 Pages

  5. G2183

    2 Pages

  6. DX900+

    4 Pages

  7. R111LM Chirp

    6 Pages

  8. PM111LH Chirp

    6 Pages

  9. M563 Chirp

    2 Pages

  10. B785M Chirp

    2 Pages

  11. DST800

    2 Pages

  12. SmallBoat CHIRP

    6 Pages

  13. SB264

    2 Pages

  14. In-Hull

    6 Pages

  15. NMEA Converters

    2 Pages

  16. Speed Sensors

    2 Pages

  17. Transom-Mounts

    2 Pages

  18. P79 In-Hull

    2 Pages

  19. B117 Thru-Hull

    2 Pages

  20. P319 Thru-Hull

    2 Pages

  21. LB150

    4 Pages

  22. PB200

    4 Pages

  23. PB150

    2 Pages